1) strength
混炼胶强度
1.
The results showed that proper increase of the raw SIBR Mooney viscosity would not affect the processibility of compound,but the strength of mix increased,the physical properties and dynamic properties of vulcanizates were improved;the comprehensive properties of high Mooney viscosity SIBR were better,and similar to SSBR1204.
结果表明,适当提高SIBR生胶的门尼粘度,可以在不影响胶料加工性能的前提下,提高混炼胶强度,同时硫化胶的物理性能和动态力学性能也普遍得到改善。
2) mixing
混炼
1.
The experimental study of polyester short fiber enhanced tread rubber mixing process;
聚酯短纤维增强胎面胶混炼工艺的实验研究
2.
Rheological property of HAF-filled powdered SBR during mixing;
HAF填充型粉末SBR的混炼流变性能
3) mix
混炼
1.
The power curve sontrolling method for discharging batches from an internal mixer is a new technique to mix rubber in the internal mixer,which can govern the mixingprocess by adjusting the power curve.
用功率曲线控制密炼机排胶的方法是控制密炼机混炼工艺过程的方法之一。
4) compounding
混炼
5) mixing mechanism
混炼机理
1.
Elaborated on the structure characteristics and mixing mechanism of VCMT synchronous rotor with 6-wing,and through experiments analyzed the effect of VCMT synchronous rotor with 6-wing on carbon black dispersion and rubber mechanics performance.
详细阐述了六棱VCMT同步转子的结构特点、混炼机理,并通过实验讨论了六棱VCMT同步转子对炭黑分散性及胶料力学性能的影响。
2.
The mixing mechanism of a new kind of extruder-series disc extruder was studied.
文中阐述了一种新型连续混炼设备———串联式磨盘挤出机的混炼机理 ,采用串联式磨盘挤出机和同向平行双螺杆挤出机对聚苯乙烯 /四氧化三铁 /丙烯酸、高密度聚乙烯 /纳米氢氧化镁进行挤出混炼效果研究 ,通过显微照片和图像分析对共混物微观混炼效果进行数学统计分析 ,发现串联式磨盘挤出机混炼性能明显优于同向平行双螺杆挤出机 ,而且改变其磨盘间隙及螺杆转速可以达到不同的混炼效果。
3.
Based on the development of the WXJ-140 reciprocating single screw pin-barrel extruder,the design principle,dynamic simulation of the plasticating system and driving system,mixing mechanism,fluid flow and mix inside the screw elements,and the experimental measurement and modeling of the residence time distribution in the extruder were studied here.
本文以WXJ-140往复式单螺杆销钉挤出机的研制开发为主线,对往复式单螺杆销钉挤出机的设计原理、挤压系统和传动系统运动仿真、混炼机理、螺纹元件内物料三维动态流动过程以及停留时间分布测量和建模等方面进行探索和研究。
6) Mixing component
混炼组件
参考词条
补充资料：炼胶
分子式：
CAS号：
性质：用炼胶机将生胶或胶料进行捏炼的操作叫炼胶。生胶单独捏炼，以提高其可塑性为目的称塑炼。塑炼好的生胶与配合剂炼合称混炼。混炼胶在压延、压出、装模之前，为进一步增加塑性、提高质地均匀性和促其软化，用开炼机炼合加热称热炼。为使混炼胶中的配合剂充分分散，用开炼机小辊距薄通称精炼。
CAS号：
性质：用炼胶机将生胶或胶料进行捏炼的操作叫炼胶。生胶单独捏炼，以提高其可塑性为目的称塑炼。塑炼好的生胶与配合剂炼合称混炼。混炼胶在压延、压出、装模之前，为进一步增加塑性、提高质地均匀性和促其软化，用开炼机炼合加热称热炼。为使混炼胶中的配合剂充分分散，用开炼机小辊距薄通称精炼。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。