1) Fracture facet
断裂刻面
1.
The results showed that there are three kinds of fracture facets on the fracture surface:annealing twin boundary fracture facet,intergranular fracture facet and transgranular fracture facet.
结果表明:低温脆断断口上有退火孪晶界断面、沿晶断面及穿晶断面3种断裂刻面。
2) fracture
[英]['fræktʃə(r)] [美]['fræktʃɚ]
裂面;断裂
3) fault(fracture)section
断裂(裂缝)面
4) interfacial fracture
界面断裂
1.
The micro mechanism of interfacial fracture.
本文对Ni Fe喷涂界面断裂的微观机理进行了探
2.
The works of theoretic studies and numerical simulation are done on the base of interfacial fracture theory in this paper.
从界面断裂的角度出发,对三维编织CMC的断裂作了理论研究和数值分析。
5) fracture surface
断裂面
1.
Based on fracture surface check and dangerous section strength examination,the cause of roll shaft breakege was obtained,and the measures to improve strength of roll shaft were put forwar
通过对辊轴断裂面的检查和辊轴危险截面强度的校核,分析了万能轧机辊轴断裂的原因,并提出了提高辊轴强度的措施。
2.
The importance of study on fracture surfaces,fractal theory and measurements of fractal dimensions are introduced.
介绍了对混凝土断裂面进行分形研究的重要性、分形理论及混凝土断裂面分析中几种主要的分数维测量方法。
3.
The fracture surface was processed before digital image is taken.
对断裂面进行处理,采集断裂面的数字图像,然后对数字图像进行分析,重新构成断裂面,通过图像求得断裂面的分形维数和真实面积,用于分析断裂能。
6) fracture surface
断裂表面
1.
The corrosion fatigue crack growth (FCG)behaviour,the effect of applied potential on corrosion FCG rates,and the fracture surfaces were studied for high-strength low-alloy steels,titanium alloys and magnesium alloys.
针对高强度低合金钢、钛合金和镁合金进行了腐蚀疲劳裂纹的扩展FCG、外加电压对于腐蚀疲劳裂纹扩展速率的影响以及断裂表面的研究 。
2.
The research achievement and progresses on the relationship between the fractal dimension of metal fracture surface and its mechanical properties are summarized,which mainly includ the relationship between fractal dimension of fracture surface and fracture toughness,impact toughness and tensile properties.
综述了近十余年来金属断裂表面分形维数与金属力学性能之间关系的研究成果和研究进展。
3.
To overcome the difficulties in estimation of fractal dimension for fracture surfaces， anew method of fractal measurement called the projective covering method(PCM) is proposed.
为了克服粗糙表面分形测量的困难，提出一种新的测量方法──投影覆盖法（ProjectiveCoveringMethod），结合激光表面测量技术，直接测定断裂表面的分形维数Ds∈[2，3）。
补充资料：刻灰
刻灰 即“款彩”或“深刻”。刻去漆面的同时也刻去漆灰，故称“刻灰”。参见“款彩”。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条