1) End Mill
立铣刀
1.
Finite Element Modal Analysis on End Mill in High Speed Milling;
高速铣削立铣刀的有限元模态分析
2) Milling cutter
立铣刀
1.
During the use of crank milling cutter,via analyzing the heat treatment process.
锥柄立铣刀在使用过程中,部分出现脆断现象,通过对立铣刀热处理工艺、焊接工艺、金相组织的分析,找出了脆断原因是热处理操作不当所致,规范操作工艺后,提高了立铣刀的生产质量和使用寿命。
2.
Based on the variation patterns of the spindle motor power signals during the milling cutter's progressive wear out, the time domain characteristics of the mathematical model between A VB and the spindle motor power are analyzed.
根据立铣刀刀齿渐进磨损过程中主轴电机功率信号的变化特点 ,分析了主轴电机功率与刀齿后刀面磨损带面积 (AVB)间模型的时域统计特性 ,提取了反映刀具磨损状态的时域统计特征参数。
3) end milling cutter
立铣刀
1.
Three-dimension solid modeling of end milling cutter;
立铣刀3D实体模型的构建
2.
The thesis does a research on design the high speed end milling cutter and dynamic characteristics, which based on the high speed milling technology and diamond tool performance,it is great significance in application in milling of diamond tools .
目前,金刚石刀具用于车削的较多,本文基于高速铣削机理、金刚石刀具的性能,进行高速切削金刚石立铣刀的设计及动特性的研究,对促进金刚石刀具在铣削领域的应用具有重要意义。
4) helical cutter
立铣刀
1.
By analyzing helical cutter wear out characteristics, the multi sensor information fusion technique was brought forward using neural network monitoring cutter major flank wear area.
传统用单一传感器监测小直径立铣刀磨损有一定局限性 ,通过分析铣刀渐进磨损过程特点 ,提出用神经网络多传感器信息融合方法监测铣刀后刀面磨损带中部带宽 ,并在立式加工中心上验证了该融合方法的有效性和工程实用性 。
5) PCBN end milling cutter
PCBN立铣刀
1.
Based on the angle orthogonal test,the relationship between tool life and cutting parameters is investigated during precisely milling hardened steel(such as Cr12MoV)with PCBN end milling cutters.
采用角正交回归试验法研究PCBN立铣刀精密铣削Cr1 2MoV等淬火钢材料时切削用量对刀具寿命的影响 ,给出了PCBN刀具铣削淬火钢时切削用量及刀具磨钝标准的选用原则和范围。
6) end milling cutter groove milling machine
立铣刀槽铣床
补充资料：安立谛非安立谛
【安立谛非安立谛】
（术语）述记十九曰：“有差别名言者名安立，无差别离名言者，非安立也。安立者施设义。”
（术语）述记十九曰：“有差别名言者名安立，无差别离名言者，非安立也。安立者施设义。”
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条