1) Anode casting
阳极浇铸
2) anode
阳极
1.
Novel proton exchange membrane fuel cell anode configuration with enhanced CO tolerance;
质子交换膜燃料电池新型抗CO阳极结构
2.
New developments of bubble behaviors on anode in aluminium smelting cells;
铝电解槽阳极气泡行为研究新动态
3) Anodes
阳极
1.
Study on Elecrochemical Characteristic of Lead-based Alloy Anodes;
电镀锌机组铅系合金阳极电化学行为的研究
2.
NiO-μm and NiO-nm in SOFC anodes,which were prepared by tape casting,were compared.
流延法制备了SOFC NiO/YSZ阳极,比较了NiO(微米级)和NiO(纳米级)两种NiO,发现由NiO(纳米级)制备的电池在800℃最大放电功率密度257。
4) anodizing
阳极化
1.
Analysis of abnormal surface colour of forged LF6 flange after anodizing;
锻造LF6法兰阳极化后表面深灰色原因分析
2.
The Phosphoric Acid Anodizing of Aluminum Alloys and the Analysis of its Adhesive Properties;
铝合金磷酸阳极化和胶接性能分析
3.
The effect of sulfuric acid,chromate acid and boric/sulfuric acid anodizing on fatigue performance of aeronautic aluminum alloys was studied by using S-N curve.
采用S-N曲线研究硫酸阳极化、铬酸阳极化和硼酸硫酸阳极化对航空铝合金疲劳极限的影响。
5) anodic polarization
阳极极化
1.
The electrochemical behavior of AZ31 Mg alloy was investigated by measuring anodic polarization curves and electrochemical impedance spectroscopy(EIS).
采用阳极极化和电化学阻抗谱(EIS)技术研究了AZ31镁合金的电化学腐蚀行为。
2.
The anodic polarization curve of iron and stainless steel in different concentration alkaline solution was studied in this paper.
通过极化曲线测量方法研究铁和碳钢在不同浓度的KOH浓碱溶液中的阳极极化行为,结果表明铁和碳钢在浓碱溶液中表现出典型的活化—钝化金属特性。
3.
The anodic polarization curves of deposits in NaOH solution were measured.
采用扫描电镜观察了碱蚀前后Ni–Co合金镀层的表面形貌,并测定了镀层在w=10%的NaOH溶液中的阳极极化曲线。
6) sacrificing anode
牺牲阳极
1.
To mitigate the corrosion damage on the tank walls,the sacrificing anode cathodic protection system has been installed in 4 drums.
鉴于中国石化集团青岛石油化工有限责任公司原来阻火水封罐和分液罐有腐蚀穿孔的情况,为了减轻火炬系统主要压力容器阻火水封罐和分液罐的罐壁受腐蚀性介质侵害的程度,在4个新罐内改装了牺牲阳极的阴极保护系统。
2.
The basic mechanisms and functions of cathodic protection are described, the design of sacrificing anodes and applied current and their respective advantages and disadvantages are compared and their economics is quantitatively analyzed based upon the case study.
阐述了阴极保护的基本原理及功能,分析比较牺牲阳极法与外加电流法两种保护方案的配置方式及其优缺点,结合工程实例对两种配置系统的经济效益进行了定性分析。
3.
The synthesis of benzoic acid using aluminium slice as sacrificing anode was studied.
本论文以牺牲阳极法合成了苯甲酸，采用红外光谱、紫外光谱、高效液相色谱等对反应产物进行定性表征，以紫外分光光度法对苯甲酸进行定量测定。
参考词条
补充资料：浇铸塑料
分子式：
CAS号：
性质：也称浇铸塑料。可注入模腔或用其他方法引入模腔、在不加压或稍加压而形成一定形状固体制品的液态树脂混配料。以它制得塑料制品时，具有流动性大和收缩率小的特点。如酚醛、氨基、不饱和聚酯和环氧等热固性塑料；聚丙烯酸酯类和聚酰胺等热塑性塑料。单体浇铸尼龙和有机玻璃浇铸板是热塑性塑料的典型代表。多用于制作板材、电绝缘器材、齿轮、滑轮、装饰品和其他制品。
CAS号：
性质：也称浇铸塑料。可注入模腔或用其他方法引入模腔、在不加压或稍加压而形成一定形状固体制品的液态树脂混配料。以它制得塑料制品时，具有流动性大和收缩率小的特点。如酚醛、氨基、不饱和聚酯和环氧等热固性塑料；聚丙烯酸酯类和聚酰胺等热塑性塑料。单体浇铸尼龙和有机玻璃浇铸板是热塑性塑料的典型代表。多用于制作板材、电绝缘器材、齿轮、滑轮、装饰品和其他制品。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。