1) Defibration
热磨
1.
An Attempt to Analyze Defibration of Wood Chip Using Multiply Monte Carlo Arithmetic;
多重蒙特卡罗算法在木片热磨过程中的应用初探
2) Abrasive wear at elevated temperature
热磨料磨损
3) defiberator-refiner plate
热磨机磨片
1.
The maximum stress and deformation of the refiner plate have been obtained through the thermal stress analysis of the sector of the defiberator-refiner plate.
通过对扇块分区热磨机磨片进行热应力分析,得到磨片的最大应力值和最大变形,并运用ANSYS的优化模块对磨片进行结构优化设计,得到了能够满足各项性能要求的新磨片,并最终达到了产品设计的轻量化要求。
4) thermal abrasion
热蚀;热磨蚀
5) grinding heat
磨削热
1.
The grinding heat is the important factor to influence greatly on the ground surface quality when the forfex is machined with gringing wheels.
砂轮磨削刀剪材料的过程中产生的磨削热是影响刀剪表面质量的重要因素。
2.
It was found that the grinding process was unsuitable,thus too much grinding heat was produced and near surface zone of the cam shaft was overtempered,which resulted in very high residual tensile stress and drop in hardness in this zone.
认为磨削工艺不当，产生了过高的磨削热，使凸轮浅表层组织回火过度，硬度大幅下降，从而产生极大的拉应力是磨削裂纹产生的主要原因。
3.
Grind-hardening is a new technology which utilizes grinding heat to induce martensitic phase transformation and strengthen workpiece surface in gringding process by raising surface temperature above Ac3 instantaneously and cooling quickly.
磨削表面强化技术利用磨削过程中生成的磨削热使工件表层温度瞬间升高到Ac3以上,然后迅速冷却,以使表层材料马氏体化。
6) Wear-resisting and heat-resisting
耐磨耐热
1.
Research on the wear-resisting and heat-resisting deposit welding rode;
耐磨耐热堆焊焊条的制备研究
2.
The wear-resisting and heat-resisting deposit welding rod with Ni-Co-Cr-B-C as the basic alloy system was prepared by mechanical ball milling mixture, sintering after extrusion shaping method.
选择Ni-Co-Cr-B-C为基本合金体系,经过机械球磨混合、挤压成形、真空烧结方法制备了耐磨耐热堆焊焊条,采用钨极氩弧焊在高温铸造合金基材上堆焊耐磨耐热堆焊层,对堆焊层的组成、结构进行了分析,XRD分析和热力学计算表明焊层组成为Co、Ni为主的面心立方合金、M23(C,B)6或M23C6,还有少量的C7M3和M3B2。
补充资料：预热热磨机械浆
分子式：
CAS号：
性质：又称预热木片磨木浆。本片洗净后，经短时间预热(100℃以上)处理，然后在常压或加压下用盘磨机磨解所得的纸浆。与其他机械浆相比，具有强度大、纤维束含量低的特点。缺点是纤维较挺硬，结合力差，生产能耗高。主要用于抄造新闻纸、低档印刷纸和中等质量涂布纸。
CAS号：
性质：又称预热木片磨木浆。本片洗净后，经短时间预热(100℃以上)处理，然后在常压或加压下用盘磨机磨解所得的纸浆。与其他机械浆相比，具有强度大、纤维束含量低的特点。缺点是纤维较挺硬，结合力差，生产能耗高。主要用于抄造新闻纸、低档印刷纸和中等质量涂布纸。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条