1) six-high mill
六辊轧机
1.
Effect of backup roll driven in six-high mill on strip shape;
六辊轧机支撑辊传动对带钢板形的影响分析
2.
Finite element analysis of the rigidity characteristics of a six-high mill;
六辊轧机刚度特性有限元分析
3.
Rolls' deformation and roll force distribution between rolls on a six-high mill are calculated by influence function method to study the influence of single-taper crowned intermediate rolls on the roll force distribution between rolls and transverse distribution of strip thickness.
用影响函数法计算了六辊轧机的辊系变形和辊间压力分布,研究了单锥度中间辊对辊间压力分布和轧件横向厚度分布的影响·结果表明采用单锥度中间辊可改善辊间压力分布状态,明显降低辊间压力峰值,但轧件横向厚差稍有增加,最大值出现在轧件边部·计算了不同锥度时的辊间压力分布与轧件横向厚度分布,通过比较辊间压力峰值与轧件边部厚度,确定了最佳锥度范围为1/100～1/150,使HC轧机的辊间单位压力峰值降低15%～20%,轧件横向厚差仅在边部增加几微米,符合板形要求
2) 6-h mill
六辊轧机
1.
The results set the basis to determine reasonable technical institution for 6-h mill.
Shohet的影响函数法和弹性基础梁模型计算了六辊轧机的辊间压力随中间辊的抽动时的变化规律 ,并用三维光弹性应力分析法进行了实验论证 ,从而为六辊轧机确定合理的工艺制度奠定了基础。
3) high UC mill
六辊UC轧机
1.
Prediction and control of chaos in the rolling process of a 6-high UC mill;
六辊UC轧机轧制过程混沌的预测和控制
4) 6-H cold mill
六辊冷轧机
1.
At present,UCM (Utility Crown Mill),CVC (Continuously Variable Crown) and VCMS (Variable Crown Middle Roller Shift) models of 6-H cold mills are widely adopted by domestie steel producers.
目前在国内流行的六辊冷轧机机型有UCM(Utility Crown Mill)、CVC(continuously Variable Crown)和VCMS(Variable Crown Middle Roller Shift),本文对这三种机型及其主要特点进行了比较,为今后用户进行机型选择提供了参考意见。
5) six high mill
六辊式轧机
6) six-high finishing rolling mill
六辊精轧机
1.
This paper mainly describes composition of six-high finishing rolling mill in the rolling thin-copper strip,the two different main-drive ways of work-roll drive and middle-roll drive,analyzing-comparing the two main-drive ways.
本文主要描述了在薄铜带轧制中六辊精轧机的组成,工作辊传动和中间辊传动两种不同的主传动方式,并对两种主传动方式进行了对比分析。
补充资料：宝山钢铁(集团)公司热轧带钢厂粗轧机组后的辊道保温
宝山钢铁(集团)公司热轧带钢厂粗轧机组后的辊道保温
宝山钢铁(集团)公司热轧带钢厂粗轧机组后的辊道保温
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条