1) deformation
[英][,di:fɔ:'meɪʃn] [美]['difɔr'meʃən]
变形量
1.
Bearing capacity analysis of self-balanced load test pile under the control of limit state and deformation
极限状态及变形量控制下自平衡试桩承载力分析
2.
The static softening behavior of hot deformation austenite of pipeline steel X60 and low-carbon bainitic steel JB700 were studied on MMS-100 thermal simulator,the effects of deformation temperature,strain magnitude and isothermal time on static softening rate were analyzed.
随变形温度、道次停留时间及变形量的增加,道次间隔时间内的静态软化量也增加,奥氏体再结晶越容易发生。
3.
Measuring technique of deformation of a T-shape cross-sectional casting when machined is studied and a simple,accurate measuring method is given.
结果表明,不同的冷却方式下其变形量不同,空冷产生的变形量最大为116μm,去应力退火产生的变形量较小为50μm。
2) deformation amount
变形量
1.
The relations between mechanical properties and the deformation amount were studied.
采用静液挤压工艺对W6Mo5Cr4V2高速钢进行静液挤压变形强化,研究W6Mo5Cr4V2高速钢经静液挤压变形后力学性能与变形量的关系,及变形量、模角等工艺参数对静液挤压过程的影响,确定静液挤压W6Mo5Cr4V2高速钢的最佳工艺。
2.
Through the testing of the electric batch annealing process for quality carbon steel 45, the influence of deformation amount and carbon mass fraction on performance was fund, annealing of spheroidizing and recrystallizing was realized simultaneously.
通过对优质碳素钢45钢在电热罩式退火炉球化退火工艺的试验,找出变形量与碳质量分数对性能的交互影响作用,实现球化退火和再结晶退火合二为一,降低工序成本,提高生产率,更好地满足用户需求。
3.
The influences of surface quenching parameters, especially the quenching moving speed, on hardness of guideway surface, deformation amount, cracking tendency, and the influences of chemical composition of casting on surface hardness and depth of hardened layer was investigated.
研究了淬火工艺参数,特别是淬火移动速度对导轨表面硬度、淬火层深度、变形量以及产生裂纹的倾向的影响,以及铸件的化学成分对表面硬度、淬硬层深度的影响。
3) deformation quantity
变形量
1.
Foundational study on relationship between deformation quantity and joining strength of rolled aluminum alloy laminated plates;
轧制铝合金叠层板变形量与结合强度的关系初探
2.
The recrystallization activation energy of Al - 5Mg alloy was calculated, and the effect of deformation quantity on the recrystallization activation energy of the alloy was studied.
根据公式G=G0exp(-Q/RT)计算了Al-5Mg合金再结晶激活能(Q),并探讨了变形量对其再结晶 激活能的影响。
3.
Influence of deformation quantity on recrystallization kinetics of Cu - 4Zn alloy is introduced, and the result obtained is of definite significance for making recrystallization processes of Cu-4Zn alloy.
介绍了变形量对Cu—4Zn合金再结晶动力学的影响,所得结果对制订Cu—4Zn合金的再结晶工艺具有指导意义。
4) amount of deformation
变形量
1.
Hot rolling technological test of sintered plates of Mo-1 has been introduced and the influences of deformation temperature,amount of deformation and annealing temperature on quality and properties of plates have been studied in this paper.
本文介绍了Mo-1牌号粉末冶金烧结板坯的热轧工艺试验,主要研究了加热温度、变形量、退火制度对板材质量、机械性能等的影响,并通过试验找出了钼板的最佳生产工艺。
2.
Beginning with the a-nalysis of tubing deformation, the amount of deformation caused by piston effect, bulking effect, temperature effect and tubing bending was worked out, and thus the calculating method and formula of bending a-mount and length were provided by mea.
从油管的变形分析入手,给出了活塞效应、鼓胀效应、 温度效应以及油管弯曲等原因造成的变形量,并在此基础上利用管柱稳定计算原理提出了弯曲个数、弯曲段长度 等关键参数的计算方法和计算公式,以期对防止偏磨提供一定的参考。
3.
And the testing experiment of amount of deformation and deformation force was carried out on the flexible gear of the XB1-100-80 modeled machine.
针对新型弹性波发生器的提出,建立了谐波齿轮传动柔轮变形与变形力的计算模型,并对XB1-100-80机型的柔轮进行了变形量与变形力测试实验,通过对测得的实验数据进行拟合分析,对柔轮变形与变形力的计算模型进行了修正,为新型弹性波发生器的设计提供了理论依据。
5) deformation degree
变形量
1.
The recrystallization behaviours of Ta-Ti alloy wires with various deformation degrees were studied.
对不同变形量的合金丝进行了再结晶退火试验。
2.
Deformation twinning of cast magnesium alloy AM60 was investigated by compression at room temperature with various deformation degrees from 3.
在电子万能试验机上对铸态AM60镁合金进行室温压缩试验,研究了在变形量分别为3。
3.
The influence of deformation degree on intergranular corrosion of hot rolled plate of 2519 aluminum alloy was studied by chemical soak experiment and metallographic analysis.
用化学浸泡实验与金相实验相结合的方法,研究了热轧变形量对2519铝合金板材晶间腐蚀的影响,结果表明,在变形温度和变形速率一定的条件下,变形量的不同导致晶界析出相分布不均和晶粒的尺寸与形状的不同,变形量愈大的2519铝合金热轧板表现出的晶间腐蚀速率也愈快;室温条件下,2519铝合金在3。
6) shapede formation
形状变形量
补充资料：岩石变形模量
岩石变形模量
deformation modulus of rock
yanshlb一anx一ngl下旧1一ang岩石变形模里(deformation modulus of roek) 指强度极限范围内的岩石应力应变之比。是岩石物理力学性质之一。在作反复加卸载试验时，岩石的总变形包括弹性变形和永久变形两个部分。岩石的变形模量ED为加在岩石上的应力与总变形之比，即 J八 百「一— 一’￡。十Cp式中氏为岩石所受的应力;‘为岩石的可恢复变形;哪为岩石的不可恢复变形。 (周昌达)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条