1) Wearing stage
磨损阶段
2) Stage grinding and stage separation
阶段磨选
3) stage-wise grinding
阶段磨矿
1.
At present,two kinds of flowsheets are adopted in Qidashan Beneficiation Plant-"stage-wise grinding-gravity separation,magnetic separation and anion reverse flotation" and"continuous grinding-low intensity magnetic separation,high intensity magnetic separation and anion reverse flotation".
目前选别齐大山铁矿石的工艺流程分别为"阶段磨矿、重-磁-阴离子反浮选"和"连续磨矿、弱磁-强磁-阴离子反浮选"。
2.
It is then determined that the flowsheet of stage-wise grinding—gravity separation—high intensity magnetic separation-anion reverse flotation is most reasonable for beneficiation of poor hematite from Gongchangling Mine.
在对弓长岭贫赤铁矿石性质研究的基础上, 从合理工艺流程的角度对试验数据进行分析, 确定阶段磨矿、重选 强磁 阴离子反浮选工艺流程为处理弓长岭贫赤铁矿的合理流程。
4) stage grinding-flotation
阶段磨浮
1.
It showed that by using mixed reagent (butyl xanthate/penty1 xanthate ratio was 1∶3)and 9538 collector for sulfide mineral to intensify silver flotation and by adopting the process flow of stage grinding-flotation,the silver recovery rate reached 94.
试验研究结果表明 :选用丁基黄药和戊基黄药适宜比例 (为 1∶3)及 95 38硫化矿物捕收增效剂来强化银的浮选 ,采用阶段磨浮工艺流程 ,可获得银回收率为 94 。
5) stage grinding and leaching
阶段磨浸
6) Stage grinding
阶段磨矿
1.
Based on process mineralogical characteristics of villaninite,a process of "stage grinding,stage flotation,and concentrate discharge from two points" was adopted.
根据该硫化铜镍矿的工艺矿物学特点,采用阶段磨矿、阶段浮选、两点出精矿的选矿流程。
2.
The experimental studies on stage grinding and leaching of high sulfurcontaining gold concentrate of Rusan District are made.
对乳山地区高硫金精矿进行了阶段磨矿、阶段浸出的试验研究。
3.
After the process mineralogical study and beneficiation experiments on ores from Dagushan and Yanqianshan,and lean magnetite ore from Gongchangling,it is concluded that a process consists of stage grinding,single magnetic separation,and fine screening-regrinding is technically advanced and feasible in treating lean magnetite ores from Anshan.
通过大孤山矿石、眼前山矿石及弓长岭贫磁铁矿石的工艺矿物学研究和选别试验研究,认为采用"阶段磨矿,单一磁选-细筛再磨流程"处理鞍山贫磁铁矿石是先进的、合理的。
补充资料：表面磨损
分子式：
CAS号：
性质：两表面接触并作相对运动所产生的微弱摩擦导致了缓慢的材料消耗。根据相对运动的特点，分成滑动磨损，转动磨损，冲击磨损三种。通常认为接触压力较小，表面材料消耗不大的属表面磨损，相反的情况，可归入表面磨耗。
CAS号：
性质：两表面接触并作相对运动所产生的微弱摩擦导致了缓慢的材料消耗。根据相对运动的特点，分成滑动磨损，转动磨损，冲击磨损三种。通常认为接触压力较小，表面材料消耗不大的属表面磨损，相反的情况，可归入表面磨耗。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条