说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 交叉点
1)  intersection [英][,ɪntə'sekʃn]  [美]['ɪntɚ'sɛkʃən]
交叉点
1.
The construction and support at tunnel intersection are introduced,and provides the solvent for the construction way and problem in intersection,which can provide a reference and sprend for the safe construction.
介绍了巷道交叉点的施工及支护方式,对各交叉点的施工方式及存在的问题,提出了解决的办法,为安全施工可借鉴推广。
2.
In order to solve this problem,based on the engineering case at the solid crossed intersection of single engine roadway and water.
为了更好地解决交叉点难支护的问题,结合鹤岗矿务局兴安矿四水平单机车线与水仓十字交叉点的工程实例,提出了柔层桁架支护的原理,基于FLAC3D软件,模拟了柔层桁架技术在深部中生代软岩巷道交叉点支护中的可适用性。
3.
The successful application of bolting and shotcreting with wire mesh in the big intersection construc- tion in Haizi Coal Mine,which provides good support example for big section road with soft rock and offers a certain value on the spreading and use.
锚梁网索喷支护技术在海孜矿大交叉点施工中的成功应用,在松软岩层中施工大断面巷道、在支护方式上提供了很好的范例,具有一定的推广和使用价值。
2)  crossing point
交叉点
3)  crossover [英]['krɔsəʊvə(r)]  [美]['krɔs'ovɚ]
交叉点
1.
Single satellite crossover differences of Jason-1 to T/P are also calculated and compared.
基于共线平差方法,比较了同步运行段Jason-1两种观测数据和T/P观测数据的有效波高、后向散射系数、各项地球物理改正以及改正后的海面高,解算比较了两颗卫星的各自单星交叉点不符值。
2.
With the data sampled near the crossover, harmonic analysis is performed to derive constants of 12 constituents( S a,S sa ,M m,M f,Q 1,O 1,P 1,K 1,N 2,M 2,S 2,K 2 ).
讨论了由卫星测高数据进行潮汐分析的混叠问题和分潮的可分辨性;用TOPEX/PO-SEIDON海面重复轨迹交叉点测高数据计算南中国海12个分潮(Sa,Ssa,Mm,Mf,Q1,O1,P1,K1,N2,M2,S2,K2)的调和常数;用不同方法验证了计算结果的精度,分析表明,分潮的振幅精度和潮高精度已达到±2cm,四个较大分潮(O1,P1,K1,M2)的迟角误差不超过±7°。
4)  cross point
交叉点
5)  crossover point
交叉点
1.
According to the inhomogeneity of altimeter data distribution over ocean, the authors propose two methods for weighting in altimeter data processing, one for crossover points and the other for non crossover points.
根据卫星测高数据分布所具有的低纬时稀疏、高纬时密集的特点,提出了计算平均海平面时非交叉点数据的解析定权公式和交叉点数据的解析定权公式。
6)  point of intersection
交叉点,交点
补充资料:闭式单点、双点压力机
代码:00413
设备名称:闭式单点、双点压力机
型号规格:公称力≥800kN
计量单位:台
主要参数内容
国际先进国内先进国内一般国内落后评定方法及说明
(一)加工精度
    参照GB10924-89、GB10933-89、JB5200-91
1、滑块下平面对工作台上平面的平行度(mm)
30%精度储备20%精度储备达到规定值大于规定值 
0.02+0.10/100×滑块下平面的被测长度
     
2、滑块行程对工作台上平面的垂直度
30%精度储备20%精度储备达到规定值大于规定值 
0.05+0.02/100×滑块行程长度
     
(二)结构性能
     
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50%
大于规定值10%大于规定值达到规定值达不到规定值 
2、液压超负荷保险装置、微调装置、吨位指示器
全部具有全部具有部分具有没有 
(三)噪声dB(A)
     
1、公称力≤400kN
≤85≤87≤88>88 
2、公称力>400kN
≤87≤88≤90>90 
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条