1) tape casting
流延
1.
Fabrication of Ni-YSZ/YSZ compound substrate membranes using tape casting method and performance measurements;
流延法制备Ni-YSZ/YSZ复合基膜及性能测试
2.
Al_2O_3/3Y-TZP laminated composite was fabricated using the tape casting and hot-press sintering.
采用流延制膜和热压烧结工艺制备了Al2O3/3YTZP层状复合材料。
3.
Castor oil was used as the dispersant of AlN tape casting slurry, its efficiency was evaluated by the method of deposition.
采用沉降法测定蓖麻油在ＡｌＮ流延浆料中的分散效果。
2) Casting
[英]['kɑ:stɪŋ] [美]['kæstɪŋ]
流延
1.
Numerical Simulation of Heat Transfer Process of Plastic Film Prepared through Casting Method;
流延法生产塑料薄膜传热过程数值模拟
2.
Development of Collagen Protein Casting Film;
胶原蛋白流延薄膜的研制
3.
In order to define a suitable method and technological parameter to dry the PVA water-soluble film by casting on steel band,in this paper,customary proportion of industrial PVA hydrosols was studied.
为了确定钢带流延法生产PVA水溶膜合理的干燥方法和工艺参数,本文以工业上常用配比的水溶胶为研究对象,先对其进行热风薄层干燥试验,在改变热风温度、风速等因素的情况下对干燥成膜进行了研究,并进行了回归分析,获得了膜层热风干燥方程,采用Page方程拟合,可较好的描述水溶胶热风干燥过程中膜层含水率与干燥时间的关系;随后,经分析得出红外辐射应用于水溶胶干燥的可行性,紧接着对试样进行了红外辐射干燥和热风/红外联合干燥的正交试验,并对三种干燥方法的试验结果进行了分析和研究,得出了水溶胶膜层的干燥特性;最后,为寻找工业生产中的水溶膜干燥成膜合理工艺,对实际生产中的水溶膜质量控制进行了探讨,并在工业应用的生产线上加装红外加热装置,进行了热风/红外联合干燥多因素正交试验,研究分析了各因素对试验指标的影响,确定了合理的组合工艺参数。
3) tape-casting
流延
1.
Organic additives play a pivotal role in the tape-casting slurry.
有机添加剂是流延料浆的关键组元,它们对料浆和流延生坯的性能有很大的影响。
4) casting drum
流延鼓<流延机>
5) casting head
流延头<流延机>
6) tape casting
流延成型
1.
Si_3N_4 ceramics were prepared by aligning theα-Si_3N_4 whisker in the substrate via tape casting and hot-press sintering.
利用流延成型使α-Si_3N_4晶须在基体中定向排列,并采用热压烧结技术制备了Si_3N_4陶瓷。
2.
In this paper, some characters of the aqueous tape casting are introduced.
简要介绍了水基流延成型工艺的特点,综述了水基流延成型工艺的浆料组成、流变性能以及干燥过程的研究现状,指出了水基流延成型今后的发展趋势。
3.
Using ethanol-(methyl ethyl ketone) binary azeotropic mixtures as solvent,glycerol trioleate as dispersant,poly(vinyl butyral) as binder,glycerol and di-n-octyl-o-phthalate as plasticizer,cyclohexanone as homogenizer,the Mo-(Fe-B)-Fe mixed powders have been made into tape casting slurry.
利用此料浆 ,采用玻璃模具浇制法流延成型出颗粒分布均匀、结构致密、厚度可控、具有适宜柔韧和拉伸强度的薄层坯体。
补充资料：流延
1.扩散延展。 2.流淌。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条