1) aluminum substrate
铝基体
1.
Through two-step anodization the anodic aluminum oxide (AAO) could be obtained on aluminum substrate.
采用两步阳极氧化法在铝基体上制备多孔阳极氧化铝(AAO)薄膜,然后在其上有序纳米孔中电化学沉积过渡金属Co作为催化剂,通过催化化学气相沉积(CCVD)法制备出高度有序的定向碳纳米棒阵列。
2.
In order to use thermal barrier coatings on the top of aluminum piston in low heat emission engine , a gradient thermal barrier coatings (TBCs) is designed and fabricated with plasma spraying on aluminum substrate .
针对低散热发动机主要部件铝活塞顶部制备热障涂层的需要,本文设计并用等离子喷涂法在铝基体上制备出梯度热障层,同时对其性能与组织结构进行研究,并用自制的设备评价其隔热特性。
2) aluminum matrix
铝基体
1.
Aluminum matrix composite reinforced with continuous boron fibers was produced with B 4C coated B fiber by atmospheric plasma spraying processing.
探讨在接近铝基体熔点温度的条件下热压压力对复合材料力学性能与B/Al界面结合的影响 ,分析了B/Al界面结合状态与断口形貌及力学性能之间的关系。
3) Aluminium Matrix
铝基体
1.
Infiltration process of fiber reinforced magnesium aluminium matrix composites made by liquid infiltration was mainly studied in the paper.
溶胶—凝胶法涂覆Al_2O_3,使得纤维与镁、铝基体的润湿性有了很大的改善,为纤维增强镁、铝基复合材料的制备开辟了一个新的途径。
4) aluminum
[英][ə'lju:minəm] [美][ə'lumɪnəm]
铝基体
1.
In order to improve the deposition rate and anti-corrosion properties of electroless plating Ni-P on aluminum,effects of stabilizing agents and surface active agents on the deposition rate and corrosion resistance of electroless plating Ni-P were studied.
为了改善铝基体上化学镀Ni-P存在的镀速慢、镀层腐蚀性能差等问题,研究了稳定剂和表面活性剂对铝化学镀Ni-P镀层的沉积速度、硬度、孔隙率、结合力、耐蚀性、腐蚀电位、表面形貌等性能的影响。
2.
In this paper,alumina/titania composite films were prepared on surface of aluminum by anodic oxidation and electrodeposition.
利用阳极氧化和电沉积的方法在铝基体上制备了氧化铝/二氧化钛复合膜,通过 XRD、TG/DSC、SEM、 EDS、XPS 等分析手段对复合膜的形貌和结构进行了表征,并对复合膜的形成过程予以阐述。
5) Al substrate
铝基体
1.
Preparation of SiO_x film on Al substrate and it's adhesion;
铝基体上沉积硅氧化物薄膜及结合性能研究
6) Mg-Al matrix
镁铝基体
补充资料:135kA中间下料预焙阳极铝电解槽(抚顺铝厂)
135kA中间下料预焙阳极铝电解槽(抚顺铝厂)
赢 135kA中间下料预焙阳极铝电解槽(抚顺铝厂)
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条