1) nodulation
[英][,nɔdju'leiʃən] [美][,nɑdʒə'leʃən]
结瘤
1.
Effects of different nitrogenous compounds on growth and nodulation of Abrus cantoniensis;
不同含氮化合物对鸡骨草生长和结瘤的效应
2.
Preliminary study on the effect of low pH on the nodulation of Medicago sativa and corresponded mechanisms;
低pH条件对紫花苜蓿结瘤的影响及机制初探
3.
Study on Variation of Nodulation and Nitrogen Fixing Capacity of Different Rhizobium meliloti;
不同苜蓿—根瘤菌结瘤固氮能力变异的研究
2) clogging
[英][klɔg] [美][klɑg]
结瘤
1.
Analysis on Clogging of Submerged Entry Nozzle for 409L Stainless Steel Concasting and Improved Measure;
409L不锈钢连铸浸入式水口结瘤分析和改进措施
2.
TiN type clogging was due to great amount of TiN inclusions,which attached to the inner wall of the nozzle.
指出含钛不锈钢结晶器"结鱼"主要是由于钢中氮钛浓度积偏高,导致TiN夹杂物大量析出,并在结晶器弯月面聚集,与保护渣反应放出氮气,致使局部钢液温度下降凝固后形成的;TiN型水口结瘤主要由于浇铸过程中TiN夹杂物附着在浸入式水口内壁造成的;TiO2型水口结瘤主要是二次氧化造成TiO2夹杂物大量增加,并在浇铸过程中附着在连铸水口内壁形成的;CaO。
3.
In order to eliminate clogging of submerged entry nozzle during concast Ti-bearing stainless steel, the phases of clogs on SEN with 321 grade were investigated by SEM and X-ray diffraction, and the mechanisms of clogging was discussed.
为了解决含钛不锈钢连铸过程中浸入式水口的结瘤问题,采用扫描电镜和 X射线微区衍射等方法分析了AISI 321不锈钢连铸水口结瘤物的物相,探讨了浸入式水口的结瘤机理。
3) accretion
[英][ə'kri:ʃn] [美][ə'kriʃən]
结瘤
1.
Through taking on complex deoxidizing and alloying process with ferro silicon manganese alloy in EBT electric arc furnace of Shiheng special steel plant the question of accretion and poor deoxidation in liquid steel is well solved Thus smooth production of continuous casting is ensured,the billet quality is increased,the production cost is decrease
石横特殊钢厂在ＥＢＴ电炉上采用硅锰铁合金复合脱氧合金化工艺，较好地解决了钢水结瘤和钢水脱氧不良的问题，确保了连铸生产顺行，提高了铸坯质量，降低了生产成本。
2.
and BF shaft wall accretion and hearth accmulation in northern side were brought about.
柳钢3号高炉于1996年3月炉况失常,高炉北面炉墙结瘤和炉缸堆积。
3.
The compositions of accretions in blast furnaces were analyzed.
分析了锌和碱金属等有害元素在炉内行为和攀钢高炉结瘤物成分及有害元素走向,揭示了有害元素对攀钢钒钛磁铁矿高炉冶炼产生的危害,锌对攀钢高炉已经产生危害,而碱金属目前未对高炉产生不良影响,但随着炉料结构的变化不容忽视,并提出了相应的应对措施。
4) scaffolding
[英]['skæfəldɪŋ] [美]['skæfḷdɪŋ]
结瘤
1.
In this paper, the causes of scaffolding in No.
分析了萍钢3号高炉结瘤原因,提出了处理措施,指出应注意改进的方向。
2.
The frequently occurred slip, hanging and scaffolding accidents in blast furnace caused by little deviation of furnace lines after overhaul in Handan Zhonghe Ironworks are introduced and it is pointed out that the furnace lines must be strictly controlled to avoid the accidents.
介绍了邯郸中和铁厂对高炉进行大修后,由于炉型微小偏差而发生的频繁崩料、悬料、结瘤事故,提出一定要严格控制高炉炉型,避免发生类似事故。
3.
It is analyzed the furnace condition getting worse and scaffolding occurred in 1# blast furnace of Han Steel from March to May of 2003 caused by change of raw material and fuel, irregular furnace lines and no in-time effective adjustment of operation system.
对2003年3月至5月份邯钢1#高炉由于原燃料发生变化、炉型不规则、操作制度没有及时有效调整引起炉况恶化并结瘤进行了分析,提出高炉操作制度必须与冶炼条件相适应,对炉况失常要早判断早调整等措施。
5) nodule
[英]['nɔdju:l] [美]['nɑdʒul]
结瘤
1.
The effect of temperature,light intensity and time of inocutating Peanut rhizobium on the growth of arachis and nodule were studied in this paper.
研究了不同时间、不同光照以及根瘤菌不同接种时间等对花生生长和结瘤的影响。
2.
The pick up nodule reason of annealing furnace roll surface was analyzed,the conventional thermal spary material lose efficacy mode was point out.
对冷轧带钢连续退火炉中炉辊表面结瘤的原因进行分析,并指出传统炉辊喷涂材料的失效形式,对开发出的新型炉辊喷涂材质的特性进行说明并与传统喷涂材料对比分析,充分显示了新型喷涂材料抗结瘤的优越性。
6) nozzle clogging
水口结瘤
1.
Study on mechanism of nozzle clogging in slab continuous casting of liquid steel refined by CAS-OB;
板坯连铸水口结瘤机理研究
2.
Analysis and control on the cause of tundish's nozzle clogging in casting ML35 steel
ML35钢浇铸过程水口结瘤原因分析及控制
3.
At last,the study of nozzle clogging is presented from the dynamics viewpoint.
水口结瘤是影响铸坯质量的重要因素,阐述了浸入式水口结瘤现象的研究现状,并概述了水口结瘤的机理,总结了目前防止结瘤的一些措施,提出从动力学角度研究水口结瘤的思路。
补充资料：瘤结
1.机体内长出的一种肿块。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条