1) finishing mill
精轧机组
1.
This paper introduces the DC drive digital control system for 1700mm finishing mill of MISCO Hot Rolling Mill, gives the control principle, characteristics, configuration and the software function.
介绍武钢热轧厂 1 70 0 mm精轧机组直流传动数字控制系统 ,说明其控制原理、特点、组成及软件功能 。
2.
The finishing mill is finished rolling mill, and it is the core part of the hot strip steel production.
精轧机是成品轧机,是热轧带钢生产的核心部分,轧制产品的质量水平主要取决于精轧机组的技术装备水平和控制水平。
2) finisher
[英]['fɪnɪʃə(r)] [美]['fɪnɪʃɚ]
精轧机组
1.
A new way was presented to optimize the scheduling of finisher of hot continuous rolling mills by means of Immune Genetic Algorithm.
提出基于ＩＧＡ模型的热连轧精轧机组负荷分配的智能优化新方法，该方法具有计算 精度高、速度快等特点，且适合在线计算。
2.
The pass schedule of finisher was optimized on the basis of proportional power ratio.
基于功率成比例原则对带钢热连轧精轧机组进行负荷分配优化计算 ,建立了以各机架出口厚度为未知量的非线性方程组 ,提出了一种新的简单求解方法——平衡迭代法 ,避免了导数计算和逆矩阵的求解。
3) finishing mill group
精轧机组
1.
The problems of direct current drive system of finishing mill group in wire production line are raised in this paper, and the key to solving the problems is that taking alternating current requency control system instead of direct current drive system is discussed.
针对某钢铁公司第三型钢厂线材生产线精轧机组原直流传动系统存在的问题 ,通过技术论证 ,采用交流变频调速系统取代原直流传动系统 ,不仅使传动系统故障率大为降低 ,而且产量也大大增加。
4) finishing stands
精轧机组
1.
The existing problems were analyzed about design,manufacture and assemblage of finishing stands of domestic high speed wire rod mill Mean while,the corresponding reformation measures were put forward Based on it,the treatment time for failure of finishing stands has been decreased from fifteen hours to three hours,and the operating rate can reach over 85 percen
对唐钢国产高线轧机精轧机组在设计、制造、装配上存在的问题进行了分析 ,并介绍了针对各种问题采取的相应改进措施和创新思路。
2.
The systematic calculation method of work roll ground contour in finishing stands of hot strip m ill is developed from the points of shape control and running stabi lity of strip in rolling process.
为了解决轧制过程中带钢的板形控制和运行稳定性问题 ,建立了系统的热轧精轧机组工作辊初始辊形的计算方法 ,为实际生产中初始辊形的确定寻找了理论上的依据。
5) finishing stand
精轧机组
1.
The temperature model for the finishing stands in hot strip mill of Wuhan Iron and Steel Co.
对武钢 170 0 m m热连轧计算机控制系统中现有的精轧机组温降模型进行分析 ,并且根据长期的实践经验及大量实测数据 ,用传热理论经优化带钢热连轧精轧机组温降模型。
6) finishingmillgroupofhotstripmill
热连轧精轧机组
1.
Basedontheanalysisandstudyoffinishingmillgroupofhotstripmill,mathematicalandsimulationmodelsof finishingmillgroup’sequipmentandcontrolsystemshavebeenbuilt.
在分析和研究热连轧精轧机组生产过程的基础上 ,综合了热连轧精轧机组各设备及控制系统的数学模型和仿真模型 ,开发了相应的仿真软件 ,并已成功地应用于某热连轧生产过程计算机仿真系统中。
补充资料：15°/75°精轧机组
15°/75°精轧机组
15°/75° finishing mill train
45。机型改进而成的。高速线材精轧机组的上限速度主要受设备制造精度和机组振动的限制。150/75。机组由于将传动轴从原45。向下旋转了3。’，从而降低了传动轴同基础平面的距离，降低了机组重心，增加了稳定性，减少了振动和噪声。该机组的最大速度可达117m/S。 (李淑芳)l口/1 0 JingZno JJ之U麟擞粼，呀拼巍 15。/75。精轧机组
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条