1) anticorrosive coating
防腐蚀涂料
1.
Current status and developing trends of binders used in waterborne metal anticorrosive coatings;
水性金属防腐蚀涂料所用基料现状及发展
2.
The key to the performance of anticorrosive coating was the kind of fillings and dosage.
合理地选择颜填料的种类及其含量是决定防腐蚀涂料耐腐蚀性能的关键。
3.
The development tendency and research hotspot of five coatings such as anticorrosive coatings, coil coatings, functional coatings, green wood coatings and powder coatings in future were introduced.
综述了目前中国涂料业的发展概况,并介绍了今后发展趋势和研究热点──防腐蚀涂料、卷材涂料、功能涂料、绿色木器涂料和粉末涂料等5种涂料。
2) anti-corrosive coatings
防腐蚀涂料
1.
Aiming at the corrosion circumstances of downhole oil tubes and the needs of anti-corrosive coatings,YG series of anti-corrosive coatings for oil tubes are developed,in terms of YG-01 baking anti-corrosive coatings for oil tubes,YG-03 air-drying anti-corrosive coatings for oil tubes and et al.
针对井下油管的腐蚀环境和防腐蚀涂覆的需要,研制了YG系列油管防腐蚀涂料,包括YG-01烘烤固化型油管涂料和YG-03常温固化型油管涂料等。
2.
The present situation of anti-corrosive coatings in China is introduced.
介绍了我国防腐蚀涂料工艺的现状,指出了目前我国重防腐涂料工业存在的问题及防腐蚀涂料的最新研究动态,详细分析了其发展趋势。
3) anticorrosion coatings
防腐蚀涂料
1.
anticorrosion coatings, coil coatings, functional coatings, powder coatings a.
在"十一五"期间,中国涂料行业主要关注的5大热点课题是防腐蚀涂料、卷材涂料、功能性涂料、粉末涂料和水性木器涂料。
2.
High chlorinated polyethylene, replacing chlorinatedrubber, and modified resin as main film former are used toprepare anticorrosion coatings of good performance, reducingthe cost of production and promoting the use of newtechnology.
以HCPE和改性树脂为主要成膜物质,制备性能优良的防腐蚀涂料,降低生产成本,促进新技术应用。
3.
A water-borne epoxy was synthesized by emulsion of vinyl-monomers and epoxy resin, which can be used to prepare anticorrosion coatings with comparable properties to solvent-based ones.
采用乙烯基单体与环氧树脂乳液共聚,得到了水性环氧树脂,所配制的防腐蚀涂料性能达到溶剂型环氧树脂涂料水平。
4) corrosion protective coatings
防腐蚀涂料
1.
This article has described the applications of waterborne accylic emulsion,waterborne alkyd emulsion and waterborne 2K epoxy in waterborne corrosion protective coatings,and compared their properties of salt spray resistance and heat and humidity resistance.
简述了水性丙烯酸乳液、水性醇酸乳液和水性双组分环氧树脂在水性防腐蚀涂料中的应用,并进行了耐湿热性能和耐盐雾性能的比较。
2.
A PC(polyester epoxy) modified HCPE(high chloropolyethylene) corrosion protective coatings by blending of PC and HCPE has been developed, which could be used as an alternative of chlorosulphonated polyethylene(CSM) corrosion protective coatings.
采用酯化型环氧树脂（ＰＣ）与高氯聚乙烯（ＨＣＰＥ）共混，制得ＰＣ改性ＨＣＰＥ防腐蚀涂料，可作为氯磺化聚乙烯（ＣＳＭ）防腐蚀涂料的替代品种。
3.
The composition of the HC solar energy shielding corrosion protective coatings was described.
叙述了HC太阳能屏蔽防腐蚀涂料的基本组成。
5) anticorrosive paint
防腐蚀涂料
1.
Formulation design of anticorrosive paint and raw metarial selection;
防腐蚀涂料配方设计要点及原料选用原则
2.
Epoxy - polyurethane IPN anticorrosive paint forms film with excellent anticorrosive property and adhesion.
研制的环氧-聚氨酯互穿网络(IPN)防腐蚀涂料具有优异的防腐蚀性能和附着力。
3.
Based on epoxy diacrylate and fural amine/epoxy IPN as binder, an anticorrosive paint with excellent heat and impact resistance is developed.
以环氧丙烯酸酯与呋喃胺/环氧树脂的互穿聚合物网络(IPN)为基料,制备了耐温、抗冲击性能优良的防腐蚀涂料。
补充资料：防腐蚀涂料
分子式：
CAS号：
性质：指由底漆至面漆配套的、以防止腐蚀性介质对基材腐蚀为主要功能的涂料体系，当其用于金属底材时往往配套应用防锈底漆。该涂料在被涂基体表面上固化后形成的涂层可通过屏蔽、缓蚀或阴极保护等作用来防止基体腐蚀。其涂层的基本特性是抗水、氧、离子等，阻止渗透性好，对各种腐蚀介质的稳定性好，对被保护基材附着力强，机械性能(硬度、柔韧性、耐冲击、耐磨耗等)优良等。目前主要品种有：环氧树脂防腐蚀涂料(有胺固化环氧、聚酰胺固化环氧、环氧沥青、无溶剂环氧、环氧酚醛、线型环氧等各类)；聚氨酯防腐蚀涂料(有多羟基化合物固化、湿固化、催化湿固化、封闭聚氨酯烘干固化等各类)；橡胶树脂防腐蚀涂料(有氯化橡胶、氯磺化聚乙烯、氯丁橡胶等各类)；乙烯树脂防腐蚀涂料(有过氯乙烯、氯醋共聚树脂、偏氯共聚树脂、聚二乙烯基乙炔等各类)；酚醛树脂防腐蚀涂料；呋喃树脂防腐蚀涂料；生漆及其改性树脂防腐蚀涂料。
CAS号：
性质：指由底漆至面漆配套的、以防止腐蚀性介质对基材腐蚀为主要功能的涂料体系，当其用于金属底材时往往配套应用防锈底漆。该涂料在被涂基体表面上固化后形成的涂层可通过屏蔽、缓蚀或阴极保护等作用来防止基体腐蚀。其涂层的基本特性是抗水、氧、离子等，阻止渗透性好，对各种腐蚀介质的稳定性好，对被保护基材附着力强，机械性能(硬度、柔韧性、耐冲击、耐磨耗等)优良等。目前主要品种有：环氧树脂防腐蚀涂料(有胺固化环氧、聚酰胺固化环氧、环氧沥青、无溶剂环氧、环氧酚醛、线型环氧等各类)；聚氨酯防腐蚀涂料(有多羟基化合物固化、湿固化、催化湿固化、封闭聚氨酯烘干固化等各类)；橡胶树脂防腐蚀涂料(有氯化橡胶、氯磺化聚乙烯、氯丁橡胶等各类)；乙烯树脂防腐蚀涂料(有过氯乙烯、氯醋共聚树脂、偏氯共聚树脂、聚二乙烯基乙炔等各类)；酚醛树脂防腐蚀涂料；呋喃树脂防腐蚀涂料；生漆及其改性树脂防腐蚀涂料。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条