1) flow stress
流变应力
1.
Influence of homogenization on flow stress of Al-1Mn-1Mg alloy during hot compression deformation;
均匀化退火对Al-1Mn-1Mg合金高温压缩流变应力的影响
2.
Prediction of flow stress in TC4 titanium alloy with hydrogen at high temperature by a radial basis function neural network;
采用RBF网络预测含氢TC4合金的高温流变应力
3.
Prediction of the flow stress of a titanium alloy during hot deformation;
钛合金高温变形流变应力的预测
2) rheological stress
流变应力
1.
Through thermal simulation compression experiment of tank used aluminium alloy,the influence of rate of deformation and deformation temperature on rheological stress were analyzed.
通过对罐用铝合金进行热模拟压缩实验,分析了变形速率、变形温度等参数对流变应力的影响,计算出了该合金的材料常数,并建立了该合金稳态流变应力模型。
2.
20/s and at constant temperature in the range of 450～500 ℃ were conducted on the 35steel and 45steel on the basis of the rheological stress constitutive model of 20steel.
为了进一步研究温度和应变速率对固体金属材料的粘性性质及其流变力学特性的影响,在建立20号钢的高温流变应力模型的基础上又对35号、45号碳素钢在温度为450~550℃和等应变速率(0。
3.
The experimental results indicated that the rheological stress was influenced by both strain rates and deformation temperature,and it increased with increasing strain and tends to be constant afte.
采用圆柱试样在Gleeble-1500热/力模拟试验机上进行高温压缩变形试验,研究了2124铝合金在高温塑性变形过程中流变应力的变化规律。
3) flow stress equation
流变应力方程
4) mean flow stress
平均流变应力
1.
Finite Analysis of Temperature Field and Prediction of Mean Flow Stress during Multi-Pass Hot Strip Rolling;
热连轧带钢温度场有限元分析和平均流变应力的预测
2.
Based on the temperature model, the multipass stress strain curve and mean flow stress were predicted during the finishing rolling of 400?MPa super steel.
采用有限单元法对热连轧生产过程中沿带钢厚度方向的温度场分布进行了预测 ,计算中考虑了带钢在机架间从表面的辐射和对流传热 ,在轧制过程中与轧辊表面的热传导和变形热·在温度场模型基础上 ,同时考虑动态、亚动态及静态再结晶的影响 ,尤其是低温区形变诱导相变软化作用 ,建立了计算精轧过程应力 应变曲线的流变应力模型 ,并对 4 0 0MPa级超级钢细晶化工业轧制中各道次的平均流变应力进行了预测 ,该模型的计算结果与Sims结果吻合较好 ,反映了工业生产实
3.
The variation of mean flow stress of two kinds of low carbon steel rolled in Angang 1780 finishing mill were analyzed.
本文分析了鞍钢1780生产的两种低碳钢在热连轧过程中平均流变应力的变化。
5) steady flow stress
稳态流变应力
1.
The influence of deformation temperature and strain rate on the steady flow stress of aluminium sheet used for easy-open cans prepared by synthetical technique of high-efficient melt-treatment of aluminium and homogenization during hot compress deformation was discussed.
采用动态热模拟试验技术探讨了经高效熔体综合处理和均匀化退火后的易拉罐用铝材在高温压缩变形过程中,变形温度和应变速率对其稳态流变应力行为的影响规律。
6) Flow yield stress
流变屈服应力
补充资料：轧辊残余应力(见轧辊应力)
轧辊残余应力(见轧辊应力)
residual stresses in roll
zhagun eanyu yingli轧辊残余应力(residual stresses in roll)见礼辐应力。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条