1) rubber series
橡胶系
1.
Study on the solvent type pressure-sensitive adhesive of rubber series;
溶剂型橡胶系压敏胶的研究
2) system of oil-rubber
油橡胶系
1.
Diffusion from gas to oil or the system of oil-rubber is the primary physical phenomenon which dominates the change of the pressure It is necessary,therefore,to study the diffusion behavior from gas to liquid or the system.
因此有必要研究气体向油及油橡胶系的扩散特性。
4) NdBR
钕系顺丁橡胶
1.
Application of NdBR to tire crown compound;
钕系顺丁橡胶在轮胎胎冠胶中的应用
5) NiBR
镍系顺丁橡胶
1.
The physical properties,especially abrasion resistance and heat build up were improved by replacing NiBR with the same amount of NdBR in tire crown compound;but the mixing process had to be adjusted because of the poor processibility and lower carbon black dispersity.
在轮胎胎冠胶中以钕系顺丁橡胶等量替代镍系顺丁橡胶 ,可改善胶料的物理性能 ,尤其是耐磨性和生热 ,但工艺性能下降 ,炭黑分散度减小 ,需对混炼工艺进行调整。
2.
An experimental study was made on the properties of raw NdBR and its compound by using conventional NiBR as control.
对钕系顺丁橡胶（ＮｄＢＲ）进行生胶和胶料性能试验，并与常规使用的镍系顺丁橡胶（ＮｉＢＲ）进行对比。
6) butadiene series rubber
丁二烯系橡胶
1.
The effects on the preparation of thermoplastic elastomers by the emulsion radical graft polymerization of butadiene series rubbers were reviewed with 12 references.
对丁二烯系橡胶乳液自由基接枝共聚合制备新型热塑性弹性体的影响因素等进行了综述。
补充资料：橡胶模具、橡胶压模、橡胶硫化模
分子式：
CAS号：
性质：又称橡胶模具、橡胶压模、橡胶硫化模。用于压制橡胶产品的金属模型。一般用钢材(如45号钢)按图纸要求经机械加工而制得，并经热处理以提高其硬度及耐磨性。模具型腔与产品结构相同，型腔尺寸必须考虑不同橡胶的收缩率，在产品尺寸基础上进行放大或缩小，方可得到合适的产品尺寸。模具从工艺操作考虑还要设置流胶槽、启模口、定位销等。
CAS号：
性质：又称橡胶模具、橡胶压模、橡胶硫化模。用于压制橡胶产品的金属模型。一般用钢材(如45号钢)按图纸要求经机械加工而制得，并经热处理以提高其硬度及耐磨性。模具型腔与产品结构相同，型腔尺寸必须考虑不同橡胶的收缩率，在产品尺寸基础上进行放大或缩小，方可得到合适的产品尺寸。模具从工艺操作考虑还要设置流胶槽、启模口、定位销等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条