说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 硬度梯度
1)  hardness gradient
硬度梯度
1.
The hardness,the depth of carburizing layer,the microstructure,the hardness gradient and distortion of these carburized gears are analyzed and compared.
使用BH催渗技术,采用渗碳温度不变、缩短渗碳时间和渗碳时间不变、降低渗碳温度两种工艺对伞齿轮进行渗碳,分析了催渗处理后伞齿轮的硬度、渗层深度、金相组织、硬度梯度及变形情况,并与原工艺渗碳处理结果进行了对比分析。
2.
Through the contrast tests it is found that carboronizing process can achieve higher surface hardness and more rational hardness gradient, and that the abradability of the carboromzed parts is much higher than that of the carburoted parts.
碳硼共渗既有较高的表面硬度,又有合理的硬度梯度而且耐磨性远远高于普通渗碳件。
3.
The results show that hardness gradient becomes smooth and its peak value shifts inwards as high speed steel tools are treated by active screen plasma nitriding, their fatigue-resistant increases.
结果表明,经活性屏离子渗氮处理后,渗氮层硬度梯度变得平缓,且最高硬度不在表面,而是在距表面一定距离处,这将能提高高速钢的耐疲劳性能,改善高速钢的内在质量。
2)  microhardness gradient
硬度梯度
1.
The steel by deep nitriding possessed excellent microhardness gradient and favorable distribution of residual compressive stresses,and the contact fatigue life of nitrided steel under the given load showed a great improvement in relation to carburized 18CrNi4A steel.
深氮化试件具有优良的硬度梯度和残余压应力分布,与渗碳件相比接触疲劳寿命提高3。
2.
Nitrogen can strengthen transition zone,thus the microhardness gradient becomes gentle.
此外 ,氮的渗入有利于强化过渡区 ,从而使硬度梯度变缓 ,有利于得到单一的Fe2 B相。
3)  Hardware gradiometer
硬件梯度计
4)  mould with gradient hardness
梯度硬度模具
5)  gradient cemented carbides
梯度硬质合金
1.
Research and development of coated of gradient cemented carbides;
涂层梯度硬质合金的研究进展
2.
The development, fabrication methods of gradient cemented carbides and several crucial problems which are encountered during the sintering of the gradient cemented carbides and cermets were summarized in this paper.
综述了目前国内外梯度硬质合金涂层基体的发展现状及其制备方法 ,对梯度硬质合金涂层基体的烧结过程热力学、梯度硬质合金涂层基体制备过程中重要的工艺参数以及梯度形成机理进行了详细讨论。
6)  gradient cemented carbide
梯度硬质合金
1.
New multi-stage models of component distribution and elastic coefficient of gradient cemented carbide;
新型梯度硬质合金的组成分布函数与弹性系数模型
2.
Formation mechanism of surface ductile zones in WC-Ti(C,N)-Co gradient cemented carbide;
WC-Ti(C,N)-Co梯度硬质合金表面韧性区的形成机理
3.
Investigation on carburized predecessor matrix of gradient cemented carbide;
梯度硬质合金渗碳前驱体的研究
补充资料:工程塑料硬度的检测--巴氏硬度计
HBa-1巴 氏 硬 度 计巴柯尔 (Barcol) 硬度 ( 简称巴氏硬度 ) 最早由美国 Barber-Colman 公司提出,是近代国际上广泛采用的一种硬度门 类,以特定压头在标准弹簧的压力作用下压入试样,以压痕的深浅表征试样的硬度。巴柯尔硬度计(巴氏硬度计)作为 专门测量玻璃钢制品、增强或非增强硬塑料、铝及铝合金、黄铜、紫铜等较软金属硬度的专用检测工具 ( 特别 适用于玻璃钢制品 ),已被大多数国家或国际组织认可。美国材料试验协会( ASTM )、日本工业规范( JIS )、中国等国家相继制定 《用巴柯尔硬度计测量玻璃钢( GRP )硬度试验方法》,《纤维增强塑料巴氏(巴柯尔)硬度试验方法》GB/T3854-1983 的国家标准。因此,巴柯尔硬度计是各生产单位、计量部门在质量认证、质量监控、计量测试等方面首选的专用检测仪器。 无锡市计量科学研究所,是我国制定巴柯尔硬度检定标准的主要参与者、巴柯尔硬度最高标准器的拥有者和国产第一台巴柯尔硬度计的研制和生产单位,也是国家实验室认证的巴柯尔硬度计专业检测机构。经过二十多年的不断完善,本所生产的 H Ba 系列巴柯尔硬度计的各项性能和技术指标完全与美国 Barber-colman 公司 GYZJ 系列硬度计相媲美 。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条