说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 强度设计
1)  Strength Design
强度设计
1.
On the basis of glass fracture theories, three strength design approaches to optical glass, which are fracture probability prediction,minimum lifetime pre- diction and probability-lifetime fracture prediction, are introduced and analyzed.
玻璃没有固定的特征强度值,其强度主要由其表面裂纹的分布所决定,玻璃的强度设计需采取保守设计思想。
2.
Simulation technology of injection molding process was applied in strength design of an annular part and a glass fiber reinforced part combining with the strength design principle, and experimental validation was carried out for the annular part.
全面阐释了影响塑料结构件强度的因素及机理 ,运用注塑过程仿真 (CAE)技术和注塑件强度设计理论 ,以环形塑件和玻璃纤维增强塑件为例进行了分析 ,并对环形塑件进行了试验验证。
3.
This paper analyzes several relevant problems on the latest SY/T5322 - 2000 standards of casing strength design, discusses emphatically the formulas of triaxial tensile strength and computational method of effective external pressing load of casing in the new standards, and corrects several formulas in the new standards.
通过对套管强度设计最新标准SY/T5322-2000的几个相关问题的分析,着重讨论了标准中三轴抗 拉强度计算公式和套管有效外挤载荷计算方法,改正了标准中的几个计算公式;同时还对新旧标准套管内 压载荷计算方法进行了对比分析。
2)  intensity design
强度设计
1.
According to the theory of stress analysis,the intensity design of the thin-skinned internal pressure cylinder is analyzed in this article.
运用应力分析理论进行了内压薄壁圆筒的强度设计
2.
Otherwise,the article mostly explores structure design of TPMS basing on material selection of the shell of transmitter,intensity design of transmitter and reliability experimentation of structure,trying to perfect the theory and method of TPMS design in structure design.
重点从发射模块壳体的材料选择、发射模块的强度设计和结构可靠性试验等几个方面研究了TPMS产品结构设计,试图从结构设计上对该产品的设计理论与方法进行进一步完善。
3)  design strength
设计强度
4)  Strength equation
强度设计式
5)  equip-intensity design
等强度设计
1.
Matching of rigidity and equip-intensity design of twin torsion bar in double wishbone suspension with twin torsion bar;
双横臂双扭杆悬架中上下扭杆的刚度匹配和等强度设计
6)  strength design value
强度设计值
1.
Based on the test of 14 model slabs, this paper analyses the property in applied stage and the failure pattern of slabs reinforced with 550 cold rolled deformed bars, and presents the strength design value of the bar.
根据14块模型板的试验,对550级冷轧带肋钢筋混凝土板使用阶段的性能及破坏形态进行了分析,并提出了该种钢筋的强度设计值。
2.
Based on the tests of 16 model beams,the paper analyses the properties of failure pattern of beams reinforced with LL550 cold rolled deformed bars in applied stage, and presents the strength design value of the bar.
根据16根模型梁的试验,对LL550级冷轧带肋钢筋混凝土梁使用阶段的性能和破坏形态进行了分析,并提出了该种钢筋的强度设计值。
补充资料:疲劳强度设计
疲劳强度设计
fatigue strength,design for

   对承受循环应力的零件和构件,根据疲劳强度理论和疲劳试验数据,决定其合理的结构和尺寸的机械设计方法。机械零件和构件对疲劳破坏的抗力,称为零件和构件的疲劳强度。疲劳强度由零件的局部应力状态和该处的材料性能确定,所以疲劳强度设计是以零件最薄弱环节为依据的。通过改进零件的形状以减小应力集中,或对最弱环节的表面层采用适当的强化工艺,便能显著地提高其疲劳强度。应用疲劳强度设计能保证机械在给定的寿命内安全运行。
    1867年  ,德国的A.沃勒展示了用旋转弯曲试验获得的车轴疲劳试验结果,把疲劳与应力联系起来,提出了疲劳极限的概念,为常规疲劳设计奠定了基础。第二次世界大战中及战后,通过对当时发生的许多疲劳破坏事故的调查分析,逐渐形成了现代的常规疲劳强度设计。1945年,美国的M.A.迈因纳提出了线性损伤积累理论  。1953年,美国的A.K.黑德提出了疲劳裂纹扩展理论。之后,计算带裂纹零件的剩余寿命的具体应用,形成了损伤容限设计。20世纪60年代,可靠性理论开始在疲劳强度设计中应用。
    在常规疲劳强度设计中,有无限寿命设计(将工作应力限制在疲劳极限以下,即假设零件无初始裂纹,也不发生疲劳破坏,寿命是无限的)和有限寿命设计(采用超过疲劳极限的工作应力,以适应一些更新周期短或一次消耗性的产品达到零件重量轻的目的,也适用于宁愿以定期更换零件的办法让某些零件设计得寿命较短而重量较轻)。损伤容限设计是在材料实际上存在初始裂纹的条件下,以断裂力学为理论基础,以断裂韧性试验和无损检验技术为手段,估算有初始裂纹零件的剩余寿命,并规定剩余寿命应大于两个检修周期,以保证在发生疲劳破坏之前,至少有两次发现裂纹扩展到危险程度的机会。疲劳强度可靠性设计是在规定的寿命内和规定的使用条件下,保证疲劳破坏不发生的概率在给定值(可靠度)以上的设计,使零部件的重量减轻到恰到好处。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条