1) Equivalent plastic compressive deformation
等效压缩变形
1.
The effect of welding temperature on equivalent plastic compressive deformation of solid - state welding;
焊接温度对固态焊接中等效压缩变形的影响
2) equivalent deformation
等效变形
1.
The key problem in the numerical simulation is how to transform the given peening parameters into the equivalent nodal forces, which is solved by the equivalent deformation method proposed by the author.
在分析窄条喷丸成形的变形特点基础上 ,提出了通过等效变形实现数值模拟的方法。
3) equivalence of deformation
变形等效
1.
In this paper, a method of determination of equivalent suction based on the principle of equivalence of deformation and the stress-strain curves obtained by triaxial compression tests of intact saturated and unsaturated loess is proposed.
以常规静三轴试验得到的原状饱和黄土以及非饱和黄土的应力-应变曲线为基础,根据变形等效的原则确定某一饱和度相当的围压即为等效吸力。
4) Compression Deformation
压缩变形
1.
Compression Deformation Behavior of Semi-solid Y112 Aluminum Alloy;
半固态Y112铝合金的压缩变形力学行为
2.
Mechanical properties of A2017 alloys compression deformation in semi-solid state;
A2017合金半固态压缩变形力学特性
3.
Compression Deformation Behavior of Semi-solid Al-Si Alloy Prepared by Crystallization-controlling;
控制结晶法制备半固态铝合金的压缩变形特性
5) compressive deformation
压缩变形
1.
Study on the heating treatment methods for compressive deformation of poplar in a fixed man-made plantation;
不同热处理方法固定人工林杨木压缩变形的研究
2.
Effect of compressive deformation on microstructures and properties of infiltrated W - Cu composites;
压缩变形对钨渗铜合金微观组织及性能的影响
3.
Study on compressive deformation of porous aluminum alloy with high specific strength;
高比强多孔铝合金的压缩变形性能
6) compression
[英][kəm'preʃən] [美][kəm'prɛʃən]
压缩变形
1.
The compression tests of semi-solid AZ91D magnesium alloy have been conducted on Gleeble1500 hot simulation equipment.
结果表明:当应变速率相同时,变形温度越高,半固态AZ91D镁合金试样的变形应力就越低;当应变速率和变形温度相同时,半固态球状晶试样的压缩变形应力明显低于枝晶试样的压缩变形应力;变形量对半固态压缩试样的应力-应变关系的影响很小。
2.
The texture changes and characteristics of β matrix in Ti-16%Al-30%Nb alloy was investigated during compression at 750℃ and annealing.
研究了Ｔｉ－１６％Ａｌ－３０％Ｎｂ合金中立方β相基体在７５０℃压缩变形及退火过程中组织和织构变化的某些特征，结果表明，变形过程中｛１１１｝面平行于压缩面的取向是稳定取向，｛１１０｝面平行于压缩面的取向是不稳定取向。
补充资料：高温压缩永久变形试验
分子式：
CAS号：
性质：考察橡胶制品在高温压缩状态下永久变形的试验。测定时将试样进行一定压缩后，放在高温下保持一段时间，然后在室温下冷却2h，除去负荷后再自由恢复1h，最后测定试样高度，高温下压缩永久变形率K由下式计算。式中，h0、h1、h2分别为压缩前压缩下和恢复后的试样高度。
CAS号：
性质：考察橡胶制品在高温压缩状态下永久变形的试验。测定时将试样进行一定压缩后，放在高温下保持一段时间，然后在室温下冷却2h，除去负荷后再自由恢复1h，最后测定试样高度，高温下压缩永久变形率K由下式计算。式中，h0、h1、h2分别为压缩前压缩下和恢复后的试样高度。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条