1) gas-assisted injection molding
气辅成型
1.
Gas penetration in gas-assisted injection molding;
气辅成型过程气体穿透行为
2.
Effects of gas channel geometry in gas-assisted injection molding on gas fingering defect of part;
气辅成型中气道形状和尺寸对气指缺陷的影响
3.
Relationship between gas fingering behavior and delayed-time in gas-assisted injection molding;
气辅成型延迟时间与气指的关系
3) gas-assisted co-injection molding
气辅共注射成型
1.
Technology on tracking the moving interfaces in the numerical simulation of the filling stage of gas-assisted co-injection molding process;
气辅共注射成型充填过程数值模拟中的移动界面追踪技术
2.
Experimental investigation on gas-assisted co-injection molding process,an innovative plastic injection molding process,is conducted based on the improved equipments.
通过对现有注塑、气辅设备的改造,对气辅共注射成型工艺进行了实验研究。
4) gas-assisted co-extrusion
气辅共挤成型
1.
The gas-assisted co-extrusion combines both virtues of co-extrusion and gas-assisted extrusion.
介绍了现有气辅共挤成型的流程和气辅共挤口模的大致形状,并提出了气辅共挤成型工艺的实体和有限元模型。
2.
A new gas-assisted co-extrusion molding technique was put forward, and a theoretical model was established, based on the characteristics of gas-assisted co-extrusion.
提出全新的气辅共挤成型工艺,基于气辅共挤成型特点建立了理论模型,通过数值模拟系统研究聚合物流变性能和工艺参数对气辅共挤成型界面不稳定性的影响规律,揭示其影响机理。
5) gas-assisted injection molding
气辅注射成型
1.
On the basis of general Hele-Shaw moldel, the simulation of the effect of several important mold-ing process parameters on gas-assisted injection molding process was implemented by means of CAE technequein this paper which involves melt temperature, delay time ,prefilled polymer volume fraction and gas pressure.
本文基于Hele-Shaw模型,采用CAE技术,模拟了气辅注射成型中几个重要工艺参数:熔体温度、气体压力、延迟时间、熔体预注射量等对其成型的影响。
2.
Development of gas-assisted injection molding technology is summarized.
概述了传统气辅注射成型技术的发展 ,并详细介绍了气辅注射应用过程中的外部气辅注射、液辅注射等新技术。
3.
This article is put forward in such an circumstance,the purpose is having a research on the key technique of gas-assisted injection molding and processing parameters,which affect the gas finger at the inner wall of GAIM production.
利用Moldflow软件,对汽车结构件杂物箱进行气辅注射成型的工艺条件优化选择,经分析和讨论最终得出该制件气辅成型的最佳工艺参数为:熔体预注射量为95%,气体延迟时间为0。
6) gas assisted co-injection molding
气辅共注成型
1.
Due to coupling of the interfacial stress in multiphase-multilayer flow,the gas assisted co-injection molding process had the special flowing law and dynamic characteristic.
针对气辅共注成型中多相分层流动存在着各分层界面应力间的相互耦合,使得其成型过程具有特殊的流动输运规律和动力学特征,对气辅共注成型工艺进行了系统的实验研究。
补充资料：阳辅
阳辅 阳辅 经穴名。出《灵枢·本输》。别名分肉、绝骨。属足少阳胆经。经（火）穴。在小腿外侧，当外踝尖上4寸，腓骨前缘稍前方。布有腓浅神经和胫前动、静脉分支。主治偏头痛，目外眦痛，胸胁痛，腋下肿痛，瘰疬，脚气，腰腿痛，下肢麻痹，以及坐骨神经痛等。直刺0.5-1寸。艾炷灸3-5壮；或艾条灸5-10分钟。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条