1) electrode tip repair
修磨器
1.
The current compensating and traditional electrode tip repairing are the main solutions to welding spot quality caused by the tipwear.
电阻点焊作为汽车制造的主要焊装方式,在焊接镀锌板时,由于电极磨损剧烈导致消耗成本增加,目前对电极磨损影响焊接质量问题主要采用电流递增法以及恒速恒压修磨法解决,文中针对电流递增法能耗过高,恒速恒压修磨效率不高的缺点,提出了变速变压修磨法,利用机器人以及PLC控制系统搭建速度压力可调的修磨器平台,通过试验与传统恒速恒压力修磨法做了对比分析。
2) wheel-dresse
磨床修整器
1.
This paper discusses the application of principle of value engineering to seek the best technique peed in the S7620A grinding machine wheel-dresser technique rebuilding, so as to lower the cost, improve the efficacy and realize the better technique result.
本文通过对S7620A磨床修整器的技术改造，运用价值工程原理，寻求最佳技术方案，达到降低技术改造成本，提高效能，实现较佳的技术效果。
3) grinder finisher
磨工修整器
4) grinding
[英]['ɡraɪndɪŋ] [美]['graɪndɪŋ]
修磨
1.
The paper discusses that the production line of crack detection grinding at EAF Plant has played an important role and contribution to grade development,process improvement and quality control.
论述了电炉厂的探伤修磨生产线在品种开发、工艺改进和质量控制方面的作用和贡献。
2.
Because it is easier in the design,manufacture, grinding shaving cutter etc of axial shaving than other finishing methods,the axial shaving is always the most general method of finishing gear being used.
因为轴向剃齿所用的剃齿刀在设计、制造及修磨等诸多方面均较容易,所以轴向剃齿一直是最普遍使用的齿轮精加工方式。
3.
The appropriate grinding quantity of the separating ring in combination of bearings,and of the end face of rings are made after the correct measurement of and calculation of the assembly height,so that the assembly height and clearance of the bearing meet the requirements.
双列圆锥滚子轴承的装配高和游隙是影响其承载能力和使用寿命的两项相关技术指标,正确测量和计算装配高,对组配的中隔圈或套圈端面确定适当修磨量,才能保证合套产品的装配高和游隙达到规定的要求。
5) figuring
[英]['figə] [美]['fɪgjɚ]
修磨
1.
On the method of figuring, The computer added method on fabricating aspherical surfaces is considered as the direction of developing, the main merit is pointed as the low rate of repeating of figuring.
在非球面修磨方法方面，首先肯定了计算机辅助加工是发展的方向，指出其主要优点在于“失误”造成的反复率大大降低。
6) regrinding
再磨;重磨，修磨
补充资料：修天庭
修天庭 修天庭 自我推拿方法名。即将两手掌擦热后，来回抚摩额部。有养颜防病的作用。《杂病源流犀烛·面部病源流》：“《养性书》：热摩手心，频拭额上，谓之修天庭。连发际，二三七遍，面上自然光泽，所谓手宜在面是也。”
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条