1) cold rolled sheet
冷轧板
1.
Progress of research on inclusion induced surface defect of cold rolled sheet
冷轧板夹杂类表面缺陷研究的进展
2.
The microstructure of continuous casted plate ,cold rolled sheet and annealed sheet of 3003 aluminium alloy were observed by photo-electro metallographical machine, the mechanical properties were obtained through mechanical property test.
利用光学显微镜观察3003铝合金铸轧板、冷轧板以及冷轧板退火后的显微组织,用电子拉伸试验机进行拉伸试验,获得不同退火温度下铝板的力学性能,讨论了退火温度对该合金显微组织、抗拉强度和伸长率的影响。
3.
The macroexamination and micro-examination of the characteristics of the common cavity defect in cold rolled sheet of low carbon Al-killed steel were carried out.
对生产中常见的低碳铝镇静钢冷轧板孔洞缺陷特征进行了宏观和微观分析。
2) cold-rolled sheet
冷轧板
1.
Impact of n value upon the formability of cold-rolled sheets with two different materials;
硬化指数n对两种不同原料冷轧板成形性能的影响
2.
Structure and Texture of CSP Cold-Rolled Sheet of Low Carbon Steel DC03;
CSP-低碳钢DC03冷轧板的组织和织构
3.
Causes of linear defects on the surface of cold-rolled sheet:analysis and discussion
冷轧板表面线状缺陷成因分析与探讨
3) cold rolled plate
冷轧板
1.
By analyzing the effect difference of intermediate annealing on the properties of hot and cold rolled plates and the rolling properties of aluminium plates under various annealing conditions and tempers,the optimal production process was datermined for the finished plates used for cosmotics packaging.
确定了化妆品包装用光亮型铝材的化学成分 ,研究了中间退火对热轧板和冷轧板组织影响的差异及不同成品退火工艺下不同状态铝材的冲制性能 ,最终确定了适合现有装备状况下化妆品包装用抛光铝材的生产工
2.
Striation and spot shape defects of the cold rolled plate surface have been analyzed in this paper,and it is determined that unreasonable pass rolling force during the cold rolling production and non-uniform raw material composition and plasticity are the reasons which cause the defect.
对近期出现的冷轧板表面条痕状和点状缺陷进行分析,确定冷轧生产时道次轧制力不合理,原材料成分、塑性不均匀是导致产生缺陷的原因。
4) cold rolled strip
冷轧板
1.
Application of continuous annealing technology for cold rolled strip in Baosteel;
冷轧板连续退火技术在宝钢的应用
5) cold-rolled steel sheet
冷轧钢板
1.
The corrosion resistance of cold-rolled steel sheet was studied by electrochemical tests including linear polarization(LP)and electrochemical impedance spectroscopy(EIS).
采用线性极化、电化学交流阻抗等方法研究了冷轧钢板的耐蚀性能,同时使用线性扫描伏安法获得了冷轧钢板表面氧化物的种类及还原电位,分析了其与冷轧钢板耐蚀性能之间的关系。
6) cold-rolled sheet
冷轧薄板
1.
Experimental study of recrystallization of cold-rolled sheets produced by CSP hot bands;
CSP冷轧薄板再结晶试验研究
2.
The main production process,equipments collocation and advanced technologies of the primary cold-rolled sheet project are introduced in this paper.
介绍了莱钢冷轧薄板(一期)工程的主要生产工艺、设备配置及先进技术。
3.
Newly-built cold-rolled sheet project in Jigang is introduced and the process flows, technological characteristics and the technical parameters of main facilities in 110×104 tons continuous pickling line, 84×104 tons cold rolling line, 43×104 tons annealing line, 48×104 tons leveling line and 33×104 tons recoiling and cutting line are analyzed with emphasis.
介绍了济钢新建冷轧薄板项目的情况,重点介绍了110万t连续酸洗线、84万t冷轧线、43万t退火线、48万t平整线和33万t重卷分卷线的工艺流程、技术特点及主要设备技术参数。
补充资料：冷轧板带轧辊
冷轧板带轧辊
cold strip and sheet mill roll
Iengzha banda一zhagun冷轧板带轧辊(eold strip and sheet millroll)冷轧板带用的轧棍除老的单机座可逆式的和窄带冷轧用的外，大量的是4一6机座连续式现代冷轧机用的工作辊和支承辊，以及一部分轧制精密合金带用的20辊轧机用的轧辊(见箔材轧棍)。 工作辊要求强度高，辊身工作层硬度高，耐磨性和抗事故性能好，并要求在一定的淬硬层深度范围内硬度落差小。冷轧工作辊基本都是锻钢的，材质为gCrZ型高碳铬钢。锻造成形后，通过整体或表面淬火以及低温回火将轧辊表面硬度调整到规定值(90一looHS)，轧制有色金属时硬度可高达105HS。淬硬层深度根据材质、淬火方式和轧辊直径大小而异。大直径轧辊在使用到极限硬度值(82~85HS)时进行重淬火。近年来为了增加gCrZ型轧辊的淬硬层深度，减少重淬.节省费用，趋势是提高铬的含量，向gCr3型和gCr3Ni型发展。为了提高耐磨性，一些国家将gCrZ型钢中Cr的含量提高到5%一10%。法国一厂家研制了离心铸造高铬钢(10%Cr)轧辊，日本还研制试用工具钢类型的钢种生产冷轧工作辊。在极少数冷轧带钢轧机前架选用高硬度铸铁复合轧辊作工作辊。 支承辊除了磨损以外冷轧支承辊的主要时效方式是局部裂纹引起的工作层剥落(见棍面剥落)。所以要求轧辊有好的耐磨性、抗剥落性、耐疲劳性、强度和韧性。冷轧支承辊有锻造、铸造(整体或复合铸造)、镶套式的，材质为亚共析或共析铬钥钢，辊身硬度在55一soHS之间。适当提高含铬量有利于减少轧辊辊身裂纹，改善抗剥落性。 (文，」春杰)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条