说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 轻合金板材
1)  light alloy sheet
轻合金板材
1.
Development and application of light alloy sheet gas forming processes;
轻合金板材气压成形工艺的研究与应用
2)  light alloy foam materials
轻合金泡沫材料
3)  magnesium alloy sheet
镁合金板材
1.
Influence of intermediate annealing on microstructure and mechanical property of magnesium alloy sheet;
中间退火对镁合金板材组织和性能的影响
2.
The textures of AZ31B magnesium alloy sheets in the conditions of hot rolling, cold rolling and heat treatment were investigated, and its feature and influence to the mechanical property anisotropy were studied.
结果表明:轧制镁合金板材具有主要以基面织构为主的板织构,其基面平行于板面,其他织构组分相对较弱;冷轧后的基极密度中心围绕板横向向轧制方向旋转约18°;冷轧后在300℃热处理对织构分布特征影响不大。
4)  7A52 alloy plate
7A52合金板材
5)  aluminium alloy sheet
铝合金板材
1.
Expatiate on key parameter of aluminium alloy sheet or plate bend test.
阐述了铝合金板材弯曲试验的关键参数,介绍了弯曲试验装置,给出了弯曲试验的结果判定。
2.
Introduced abrade performance property of aluminium alloy sheet and main factors effected abrade and lubrication,through choose right lubrication,lowed deformation force of aluminium alloy sheet drawing,improved surface quality and OK parts rate,gained good economic performance.
介绍了铝合金板材拉伸成形的摩擦特性及影响摩擦和润滑的主要因素,通过选用合适的润滑剂,显著降低铝合金板材拉伸时的变形力,提高了零件的表面质量和良品率,取得了较好的经济效益。
6)  titanium alloy sheet
钛合金板材
1.
Based on FEM simulations and forming tests the cylindrical cup drawing processes of TC1M titanium alloy sheets with 0.
84mm厚的TC1M钛合金板材杯形件室温拉深成形及回弹过程进行了研究。
2.
However, it is found that the shape distortion ,which obviously appears after unloading and springback ,induces a series of dimensional and location deviation in the titanium alloy sheet parts, and it has become a serious problem in the aircraft manufacture.
并在此基础上采用有限元数值模拟和成形试验相结合的研究方法,揭示出TA2M钛合金板材扩孔成形卸载回弹后形状畸变的各类现象。
3.
A systematic analysis of the springback in titanium alloy sheet bend-forming was presented in this paper, it used the method which integrates finite element simulation and forming tests.
本文采用有限元数值模拟与成形工艺试验相结合的方法,对TA2M钛合金板材的弯曲回弹问题进行了系统的研究,揭示了弯曲线取向对回弹的影响,并对弯曲时的局部畸变现象进行了深入研究。
补充资料:东北轻合金加工厂
      中国第一个近代化的大型铝、镁合金加工厂,位于黑龙江省哈尔滨市。1954年动工,1956年建成。起初,它是为航空工业提供铝材的专用厂,后来逐步增加了民用铝材,扩大了品种。本厂产品的品种、质量在中国是第一流的,经营管理工作在有色金属行业中也居领先地位。1981年生产的产品有16类,132种合金,1813个品种,8132个规格;主要产品有铝合金板材、管材、棒材、型材、线材模压件、锻件、箔材、铝粉、合金粉、镁粉及镁合金棒材、型材、模压件等。(见彩图)
  

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条