1) room-temperature evaporation
常温蒸发
1.
In light of theorectical analysis of the phase diagram of Na+,Mg2+∥Cl-,SO2-4—H2O system,and based on experiments of low-temperature refrigeraton and room-temperature evaporation of inter-crystal brine in Tulantai salt-saltpeter lake,Inner Mongolia,the processes and parameters for the comprehensive utilization of brine were optimized.
文章在Na+,Mg2+∥Cl-,SO42-—H2O体系相图理论分析的基础上,根据详实的内蒙图兰泰盐硝湖晶间卤水,低温冷冻和常温蒸发室内实验,优化了卤水综合利用的工艺流程及工艺参数,为图兰泰盐硝湖的开发提出了技术上可行、经济上合理的卤水综合利用方案。
2) atmospheric evaporation
常压蒸发
4) evaporation anomaly
蒸发异常
5) Isothermal evaporation
等温蒸发
1.
Study on preparation of KNO_3 from the brine in Luobupo (Ⅱ) the isothermal evaporation experiment;
罗布泊卤水生产硝酸钾半成品工艺研究(二)等温蒸发实验研究
2.
Study on isothermal evaporation of salt lake brine in Lop nur region;
罗布泊盐湖卤水等温蒸发研究
3.
It is necessary to carry out an isothermal evaporation experiment at lower temperatures to understand the crystalization path of salt mnerals at ambient temperatures.
为了更好地了解卤水在自然条件下的蒸发结晶规律,需对相应卤水进行低温室内等温蒸发实验研究。
6) evaporating temperature
蒸发温度
1.
A refrigerating system for freezing fish products using two evaporating temperatures is discussed in detail by means of theoretical analysis, calculation and consideration of operating effects.
通过理论分析、计算和实际应用测定,全面阐述了用两种蒸发温度对鱼品进行速冻的制冷系统。
2.
With a designed supercooled-water ice making system test-bed, carries out grouping experiments for different evaporating temperatures and water flow rates.
在自主开发的过冷水制冰试验台上,对不同蒸发温度和水流量下的运行情况进行了分组试验。
3.
Some researches in an ice harvester machine are made which indicate that the evaporating temperature is the most significant factor which influence the COP (Coefficient of Performance) of a refrigeration compressor while both the evaporating temperature and the condensing temperature are two main factors.
通过对某冰片滑落式冰蓄冷空调系统运行的分析及研究,表明在影响制冷机COP值的两大因素——蒸发温度和冷凝温度中,蒸发温度占主导地位,要提高制冷机运行的COP值应当首先考虑提高制冷机的蒸发温度。
补充资料:常温干燥
分子式:
CAS号:
性质:在常温条件下使涂膜干燥的工艺过程,也称自然干燥或空气干燥(air drying)。干燥时的气温、相对湿度和通风状况是影响干燥的重要因素。温度一般为10~35℃,相对湿度为75%以下,室内通风量为6~10次/h;室外风速在3级(3.4~5.5m/s)以下为宜。
CAS号:
性质:在常温条件下使涂膜干燥的工艺过程,也称自然干燥或空气干燥(air drying)。干燥时的气温、相对湿度和通风状况是影响干燥的重要因素。温度一般为10~35℃,相对湿度为75%以下,室内通风量为6~10次/h;室外风速在3级(3.4~5.5m/s)以下为宜。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条