1) premixed chamber
预混腔
1.
In this paper, the characteristics of catalytic reforming reaction, coke deposition on Ni katalyst and three-dimension flow in the micro combustor premixed chamber were simulated.
因微型燃烧器内微尺度燃烧易熄火、燃烧效率不高,存在催化重整过程中的积碳、微尺度等问题,可利用甲烷和湿空气中水蒸汽预混催化重整产氢来强化燃烧,对预混腔内催化重整、积碳及流动特性进行模拟,探讨了微型预混腔中甲烷、水蒸汽重整过程中水碳比、质量流量和催化壁面温度对催化重整、积碳、流动等的影响。
2.
In this paper,characteristics of generating hydrogen from methane wet air catalytic reforming reaction on the premixed chamber wall with Ni katalyst was done with numerical simulatio.
0,对甲烷/湿空气在壁面涂有含稀土的镍基催化剂的微细预混腔中催化重整产氢特性进行了数利用碳氢燃料和湿空气中水蒸气预混催化重整产氢来强化燃烧,以实现微尺度下燃料的持续稳定高效燃烧。
3) multicavity PCRV
多腔预应力混凝土反应堆容器
4) premixed
预混
1.
Status and Trends of Frontier Fundamental Research Projects ofPremixed Turbulent Combustion;
预混湍流燃烧基础研究的现状和动向
2.
On Kinetic Mechanisms for Premixed LaminarSteady State MethaneAir Flames;
CH_4/O_2/N_2预混、层流、稳态火焰反应机理分析
3.
In this paper, numerical simulation of strained premixed methane-air flame is performed on the case of "Fresh-to-Burnt".
对甲烷 /空气对撞拉伸层流预混火焰进行了数值求解 ,所采用的化学反应机理为GRI_Mech3。
5) premixing
预混
1.
In view of contrast of Quiescent Mixing effect,modern in-blend unit of quiescent mixer is developed first,the structure of quiescent mixer is optimized,and traditional and premixing model of quiescent mixer are developed.
目前三元注入装置静态混合效果差,首先研制了新型结构的静态混合器进混单元,对静态混合器的结构进行优化设计,提出了常规和具有预混作用的两种结构模型,并应用FLUENT软件对静态混合器四相流体掺混现象进行仿真计算。
6) premix
[英][pri:'miks] [美]['pri'mɪks]
预混
1.
Numerical Simulation on Premixed Catalytic Combustion of Methane in Micro-combustor;
微型燃烧器内甲烷预混催化燃烧的数值模拟
2.
Numerical investigation of premixed catalytic combustion of methane in micro-combustor
微型燃烧器内甲烷预混催化燃烧的数值研究
3.
Based on the characteristic of MEMS technology and micro combustors,the structure of the micro combustor is ameliorated by the methods of rotational flow,adding premixing channels and export channels and predigesting devices for pipe connection.
根据微型燃烧器的特点,采用旋流预混、增设预混通道、燃气出口通道和简化管道接气装置等方法对微型燃烧器的结构进行改进设计。
补充资料：预混料
分子式：
CAS号：
性质：指橡胶与聚乙烯等塑料，或与再生胶、纤维等需要单独塑化、精炼，而预先制成的母料。
CAS号：
性质：指橡胶与聚乙烯等塑料，或与再生胶、纤维等需要单独塑化、精炼，而预先制成的母料。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条