1) solution and double-refine treatment
固溶双细化处理
2) double-fined treatment
双细化处理
1.
The crystal and carbonization are fined and dislocated martensite become increased after cold-punching die made of GCr15 steel double-fined treatment.
对GCr15钢制冷冲模采用双细化处理后,细化了晶粒和碳化物,增加了位错马氏体的数量,同时也增加了残余奥氏体量,有效地提高了GCr15钢的强韧性,从而提高GCr15钢制冷冲模的寿命。
2.
Influences of conventional heat treatment and double-fined treatment on structure and properties of cold-punching die made of GCr15 steel were compared.
比较了常规热处理和双细化处理对GCr15钢制冷冲模组织和性能的影响。
3) strengthening solution treatment
强化固溶处理
1.
After strengthening solution treatment,470℃,60min+485℃,60min,the tensile strength in solution and T6 are improved,the electric conductivity in .
结果表明:采用470℃,60 min+485℃,60 min强化固溶处理。
4) solution heat treatment
固溶处理
1.
The effects of solution heat treatment processes on the microstructure and mechanical properties of the spray deposited 7090/SiC_P composite were investigated.
研究了固溶处理工艺对喷射沉积7090/SiC_p铝基复合材料的显微组织和力学性能的影响。
2.
It is thereby shown that the spinning and bulging forming can be done successfully, when taking four paths stepped spinning process, non-completed solution heat treatment (460℃±10℃ 30 min quenching by water) before spinning and completed solution heat treatment (515℃±10℃ 15 min quenching by water) before bulging for 6061.
结果表明,以6061铝合金为材质,采取4道次错距强旋成形工艺以及旋压前进行不完全固溶处理[(460±10)℃ 30 min、水淬]、胀形前进行完全固溶处理[(515±10)℃15 min、水淬],可确保旋压及胀形过程顺利进行,壳体的凹槽形状、尺寸精度、力学性能以及表面质量均可得到有效的保证。
3.
To dissolve the intermetallics which precipitated from the matrix of the layer, a solution heat treatment is conducted.
采用双层辉光离子渗金属技术 ,首先在低碳钢表面渗入合金元素钨、钼 ;然后作固溶处理 ,使金属间化合物溶于基体中 ;接着渗碳 ,使合金层内形成大量弥散、均匀、细小的合金碳化物。
5) solution treatment
固溶处理
1.
Effect of solution treatment on the microstructure and properties of 0Cr17Mn11Mo3N steel prepared by metal powder injection molding;
固溶处理对注射成形0Cr17Mn11Mo3N钢组织性能的影响
2.
Effects of solution treatment on the microstructures and mechanical properties of Al-1.5Si-1.2Mg-0.6Cu-0.3Mn aluminum alloy sheets;
固溶处理对Al-1.5Si-1.2Mg-0.6Cu-0.3Mn铝合金组织性能的影响
3.
Effect of solution treatment on microstructure and properties of 7B04 aluminum alloy;
固溶处理对7B04铝合金组织和性能的影响
6) solid solution treatment
固溶处理
1.
Effect of solid solution treatment on microstructure and properties of MIM Cr17Mn11Mo3N stainless steel;
固溶处理对注射成型Cr17Mn11Mo3N不锈钢组织性能的影响
2.
Effects of Y addition and solid solution treatment on microstructure and mechanical properties of AM60 magnesium alloys;
稀土Y及固溶处理对AM60镁合金组织和力学性能的影响
3.
Effect of the cooling rate during solid solution treatment on the properties of 1420 alloy;
固溶处理冷却速度对1420合金性能的影响
补充资料：固溶强化合金
分子式：
CAS号：
性质：某些金属元素固溶于合金的奥氏体基体中而达到强化的高温合金。成材后的形状多为薄板。其性能特点是：不但具有优良的抗氧化和冷热疲劳性及较高的抗高温蠕变性能，而且还具有良好的冷冲压和焊接等工艺性能。这类合金主要用来制作燃气涡轮发动机和燃烧室以及火箭发动机的燃气导管和尾喷管等部件。
CAS号：
性质：某些金属元素固溶于合金的奥氏体基体中而达到强化的高温合金。成材后的形状多为薄板。其性能特点是：不但具有优良的抗氧化和冷热疲劳性及较高的抗高温蠕变性能，而且还具有良好的冷冲压和焊接等工艺性能。这类合金主要用来制作燃气涡轮发动机和燃烧室以及火箭发动机的燃气导管和尾喷管等部件。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条