1) supported liquid membrane
支撑液膜
1.
On line supported liquid membrane enrichmentflow injection spectrophotometric determination of trace cadmium(Ⅱ) in water;
支撑液膜在线萃取富集-流动注射分光光度法测定水中痕量镉(Ⅱ)
2.
Research progress of stability of supported liquid membranes;
支撑液膜稳定性研究进展
3.
Extraction of the citric acid by supported liquid membrane;
支撑液膜法提取柠檬酸——膜配方的研究
2) supported liquid membranes
支撑液膜
1.
Application of ionic liquids in supported liquid membranes;
离子液体在支撑液膜中的应用
2.
Advances in separation mechanism , explanations for instability and methods for stability improvement in supported liquid membranes during the last thirty years were reviewed in this paper, and some researches on flue gas desulfurization(FGD) using this technology were also reported.
支撑液膜技术作为一种高选择性和高渗透性的膜分离技术得到了越来越多的应用。
3.
The losing behavior of liquid in supported liquid membranes(SLMs) was studied by electrochemical impedance spectroscopy(EIS) method in this paper.
采用电化学阻抗法研究支撑液膜膜液的流失行为,并采用等效电路法分析得到的交流阻抗图谱。
3) supporting liquid membrane
支撑液膜
1.
The citric acid was extracted from citric acid solution by polypropylene supporting liquid membrane, and its mass transfer conditions in the technological process were studied.
用聚丙烯支撑液膜从柠檬酸溶液中提取柠檬酸,通过正交实验考察和分析料液相浓度、反萃取相浓度、搅拌速率、温度等因素的影响,得到最佳传质条件料液相浓度为0。
2.
The transferring behaviour of Cd(Ⅱ)ion through supporting liquid membrane was studied with porous polyproplylene membrane as supporting body and PC-88A/CHCl3 as carries;the effect of carries concentration,pH value,temperature and beginning concentration in feed phase etc.
本文以多孔聚丙烯膜为支撑体,PC-88A/CHCL3为膜载体,研究了重金属离子Cd(Ⅱ)的支撑液膜传输的行为。
4) supported liquid membrane
支撑体液膜
5) composite supported liquid membrane
复合支撑液膜
1.
Fabrication and vapor permeation characterization of a LiCl solution based composite supported liquid membrane;
基于LiCl溶液的复合支撑液膜的制备及其透湿性测定
补充资料：支撑液膜
分子式：
CAS号：
性质：指液膜溶液借助于支撑体的微孔的毛细管力含浸于支撑体内，料液中要回收的物质通过支撑体微孔中的液膜进行透过而被回收。液膜支撑体主要采用疏水性多孔膜，其性能与支撑体材料、膜的厚度及微孔大小有关，膜厚25～50μm，微孔的平均孔径为0.02～1μm，孔径越小，液膜越稳定，但孔径过小会导致孔隙率下降，从而降低透过速度。支撑体一般采用聚丙烯、聚乙烯、聚砜及聚四氟乙烯等疏水性多孔膜。其透过机理可用示意图表示。支撑液膜多用于处理水溶液。
CAS号：
性质：指液膜溶液借助于支撑体的微孔的毛细管力含浸于支撑体内，料液中要回收的物质通过支撑体微孔中的液膜进行透过而被回收。液膜支撑体主要采用疏水性多孔膜，其性能与支撑体材料、膜的厚度及微孔大小有关，膜厚25～50μm，微孔的平均孔径为0.02～1μm，孔径越小，液膜越稳定，但孔径过小会导致孔隙率下降，从而降低透过速度。支撑体一般采用聚丙烯、聚乙烯、聚砜及聚四氟乙烯等疏水性多孔膜。其透过机理可用示意图表示。支撑液膜多用于处理水溶液。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条