1) Grouting reinforcement
注浆加固
1.
Grouting reinforcement design and construction of old roads;
谈旧水泥路面注浆加固设计与施工
2.
Karst roadbed grouting reinforcement construction technology
岩溶路基注浆加固施工技术
3.
In order to make clear the effect of grouting reinforcement of broken rocks,grouting reinforcement test of post-peak rock sample was made and then the sample was tested by adopting cement slurry and Malisan N,respectively.
同时,为了研究岩石破裂后注浆加固效果,分别采用水泥浆液和马丽散N浆液对峰后岩石试件进行了加固实验。
2) grouting strengthening
注浆加固
1.
The application of grouting strengthening in subway shallow-buried subsurface excavated underground line;
注浆加固在地铁浅埋暗挖通过地下管线的应用
2.
Through analysis on relevant stratum conditions of undercutting tunnel construction from Xizhimen to Dongwuyuan in 4th line of Beijing subway,this paper discusses grouting strengthening construction technology adopted in the construction process,and proposes several opinions and suggestions according to concrete construction practice.
通过对北京地铁四号线西直门—动物园区间暗挖隧道工程相关地层特性状况进行的分析,对在施工过程中采取的注浆加固施工技术措施作了简明探讨,并根据具体施工实践,提出一些体会和建议。
3.
In this article, authors analyze and discuss the grouting strengthening design adopted in this emergency treatment.
上海轨道交通 4号线越江隧道联络通道因大量流砂涌入 ,引起隧道受损及周边地区地面沉降 ,本文就抢险中的注浆加固设计进行分析探讨。
3) grouting consolidation
注浆加固
1.
This paper presents blasting grouting consolidation technology and "U" Shaped conduction cave blasting drilling technology applied in fault zones, which result in a safe, quality and efficient effect in construction.
介绍了在断层破碎带内采用爆破注浆加固、马蹄形导洞爆破掘进技术 ,达到破碎带施工安全、优质、高效的目
2.
Combined with engineering example,the foundation was consolidated by deep layer agitating cement pile and grouting,its grouting consolidation technology and agitating pile consolidation technology were illustrated.
结合工程概况,选用深层水泥搅拌桩和注浆对地基进行加固,对其注浆加固技术及搅拌桩加固措施进行了阐述,通过采用深层搅拌桩和注浆加固技术对软弱地基进行加固,保证了超大规模沉井水沟的质量和安全。
4) grouting
[英]['grautiŋ] [美]['graʊtɪŋ]
注浆加固
1.
This paper introduced the two-step coupled grouting method to consolidate the joint,and achieved better results.
采用两步耦合注浆法进行注浆加固,取得了较好效果。
2.
Based on similar theory,the deformation properties of-440 pump with high rheological Surrounding Rock are studied by similar material experiment ungrouting and postgrouting at Wannian Coal Mine.
根据相似理论,对万年矿-440泵房高流变围岩注浆加固前后变形特性进行相似材料模拟研究,得出了其变形规律:高流变围岩变形可以分为扩帮整修加速阶段、相对稳定阶段和动压阶段等三个阶段;注浆加固使泵房围岩岩体变形由结构高流变特性转为线弹性或是弹塑性。
3.
This paper analyses the disease origin in new subgrade of the sixth speeding-up in Jing-Guang Line,proposes the measure of static press grouting in subgrade projects,and introduces in detail the subgrade strengthening plan and construction techniques.
分析了京广线第六次提速拨改地段路基病害原因,提出了静压注浆加固地基工程措施,详细介绍了路基加固方案及施工工艺。
5) grouting reinforce
注浆加固
1.
Based on theroy analysis of clamage evolution and broken process of roof coal,Malisan N produce is adopted in advance grouting reinforce in S 2-1 workface end of Changcun coal mine,it maintains stable of entry roof,safety and economic result are gained.
以顶煤损伤演化和破碎过程理论分析为基础 ,常村煤矿在S2 -1综放工作面端头超前维护中采用马丽散N产品进行超前注浆加固 ,保持了巷道顶煤的稳定 ,取得了显著的安全效益和经济效
2.
The text introduces the geology advance forecast,advance grouting reinforce and timbering,grouting effect check up and the construction process in cavity section PDK354+255～+275 of the tunnel.
本文系统地介绍了该隧道 PDK35 4 +2 5 5～ +2 75溶洞段的地质超前预测预报、超前注浆加固及支护、注浆效果的检查评定及施工过程 ,为今后类似工程的设计、施工提供借鉴依
3.
Experiments of grouting reinforcement indicate that the intensity of grouted rock mass is higher than that of non-grouted.
注浆加固实验表明,注浆岩体强度比未注浆有了很大程度的提高。
6) grouting reinforcement method
注浆加固法
1.
The application of grouting reinforcement method in quality control of large-diameter cast-in-situ pile;
注浆加固法在大直径灌注桩质量控制中的应用
2.
Taking several projects as example,the author introduces the application of partition method,grouting reinforcement method and underpinning method in the construction of Metro tunnels passing underneath surface buildings/structures.
结合不同的工程实例,介绍隔断法、注浆加固法、桩基托换法等保护方法在地铁区间隧道穿越建筑物基础时的应用及施工技术措施,并总结其适用条件,希望对类似工程的设计和施工提供一定的借鉴作用。
补充资料：电泳注浆成型
分子式：
CAS号：
性质：陶瓷浆料的成型方法之一。利用浆料中颗粒荷负电，在直流电场作用下向阳极运动而沉积在模型(阳极)上形成坯体的成型方法。此法可加快坯体形成速度，坯体较致密，可用于面砖，基板等的成型，但有时会因水的电解作用产生气泡，电场不均匀会造成坯体厚薄不均或脱模困难，故尚未得到广泛使用。
CAS号：
性质：陶瓷浆料的成型方法之一。利用浆料中颗粒荷负电，在直流电场作用下向阳极运动而沉积在模型(阳极)上形成坯体的成型方法。此法可加快坯体形成速度，坯体较致密，可用于面砖，基板等的成型，但有时会因水的电解作用产生气泡，电场不均匀会造成坯体厚薄不均或脱模困难，故尚未得到广泛使用。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条