1) screw configuration
螺杆构型
1.
A mixing performance analysis on the different screw configuration in the process of twin screw codirectional extrusion;
同向双螺杆挤出过程不同螺杆构型的混合性能分析
2.
The filling ratios in the main reactive zones were estimated by clam barrel for different screw configurations.
研究了不同螺杆构型下的充满度以及低密度聚乙烯(PE-LD)熔融接枝马来酸酐(MAH)的过程,探讨了不同螺杆构型下充满度与接枝反应挤出过程的关系。
3.
The mixing performance of different screw configurations of a co-rotating twin screw extruder and the grafting reactive extrusion of PE-LD-g-MAH were investigated.
研究了不同螺杆构型的混合性能以及低密度聚乙烯熔融接枝马来酸酐的过程,探讨了不同螺杆构型的混合性能与接枝反应接枝率的关系。
2) screw configurations
螺杆构型
1.
In the polymer compounding process, screw configurations are important factor influencing the mixing effect of the polymer blends in co-rotating twin screw extruder.
在啮合同向双螺杆挤出机对高聚物共混改性的加工过程中，螺杆构型是影响混合效果的一个重要因素。
2.
In this paper, the flow fields of the combined channels of different screw configurations in intermeshing co-rotating twin screw extrusion were analyzed.
本文利用专业CFD(Computational Fluid Dynamics)软件POLYFLOW对啮合同向双螺杆挤出过程不同螺杆构型下的组合流道进行了流场分析。
3.
For the mixing equipments,the screw configurations is the key factor in influencing the PP/PA6 blends properties.
影响PP/PA6共混体系性能的主要因素有配方、相容剂、操作条件、混合设备等,而混合设备中螺杆构型是影响共混体系性能的关键因素。
3) Screw configuration
螺杆结构
1.
To experimentally study the influence of the melt blending condition on the resulting mechanical properties of "in--situ"composites,two different screw configurations were implemented and the blends with different TLCP contents were produced to the in--situ composites.
发现不同的螺杆结构混合并不能对复合材料的力学性能造成明显的影响。
4) screw model
螺杆模型
5) special spiral rod
异型螺杆
1.
Research on tool condition monitor instrument during milling special spiral rod;
异型螺杆铣削刀具监控仪的研究
6) screw parameter
螺杆造型
1.
The effect of main screw parameters (length/ diameter ratio, helix angle, channel depth and compression ratio)of cold feed rubber extruder on extrusion temperature were investigated by orthogonal regression method on the basis of the statistical analysis of experimental results.
研究了螺杆造型（长径比，螺旋升角，螺槽深度，螺杆几何压缩比），挤出工艺（螺杆转速，机头口型）和胶料种类对橡胶冷喂料挤出机挤出温度的影响，并对各实验因素及实验结果做了统计分析，得出了他们之间的定量数学模型。
补充资料：螺蚄
1.见"螺蚌"。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条