1) pallet critical value
台车临界值
1.
The definition of characteristic section image of sintering machine plant-tail is thoroughly described and deeply analyzed for the first time,two types of characteristic section image and pallet critical value are proposed,and the calculation method of pallet critical value is demonstrated.
对机尾特征断面的出现过程进行了阐述和理论分析,提出了机尾特征断面出现的2种方式和台车临界值概念,并给出了台车临界值的计算方法。
2) critical speed
临界车速
1.
In order to obtain critical speed when articutaled-frame vehicles(AFV) drive stability, the driving stability of AFV with hydraulic steering system moving along a straight or a small curvature road was studied.
为了获得车辆稳定行驶的临界车速,对铰接式车辆沿直线或大曲率半径曲线行驶时的稳定性进行了研究。
2.
A roots-locating numerical method was used to identify critical speed.
应用一种数值寻根法分析了系统的临界车速。
3) critical point
临界值
1.
Through the comparison of critical points, the main influence factors were found out, and the task to stabilize sinter TFe and basicity in next step was pointed out.
本文分析了本钢二铁厂各种原料的主要成分及配料量对烧结矿TFe、碱度稳定性的影响;并通过对临界值的比较,确定了主要影响因素,以及稳定TFe和碱度的主要工作方向。
2.
The critical point of d-dimensional bootstrap percolation like cellular automata is studied.
研究了d维自助式类渗流细胞自动机模型的临界值问题。
3.
This paper deals with the critical point of three-dimensional bootstrap percolation-like cellular automata.
本文研究三维自助式类渗流细胞自动机的临界值。
4) EME critical value
EME临界值
5) incipient calorific value
临界热值
1.
In this paper, a thermodynamic model to predict the incipient calorific values of MSW for this novel process is proposed.
首先从热力学角度建立了城市垃圾气化熔融工艺临界热值的计算模型,具体分析了垃圾中水份、灰份和有机成份的变化对临界热值的影响。
6) threshold
[英]['θreʃhəʊld] [美]['θrɛʃhold]
临界值
1.
Preliminary study on precipitation threshold of precipitation- induced landslides in Ya an Yucheng District, Sichuan Province;
四川雅安市雨城区降雨诱发滑坡临界值初步研究
2.
The related theory that the drilling tool is affected by the inclination of the well had proved the fact:if the angle of the well is greater than a threshold,there will be se.
井斜对钻具的影响有关理论已经证明 ,如果井斜角大于某一临界值 ,在狗腿处旋转钻杆将会引起严重的疲劳破坏。
3.
The expression of rainfall threshold considering both the rainfall intensity and rainfall process was established.
论文以四川省雅安市雨城区为研究区,将逻辑回归模型引入区域降雨型滑坡预警预报,建立了同时考虑降雨强度和降雨过程的降雨临界值表达式。
补充资料：台车
圆型纬编针织机的一种。钩针固定在直立的针筒上。主要用以生产平针组织、集圈组织、添纱组织、衬垫组织、毛圈组织的内、外衣坯布和其他装饰、工业用织物。在针筒内、外两侧，沿圆周配置着一组组成圈系统。图示为台车的一组成圈系统，当针筒回转时，诸轮的钢片因与钩针相啮合而被带动。一般采用针织法成圈。编织平针组织时,由退圈圆盘压下坯布,将旧线圈退到针杆下方、再由清纱轮、清除针口乱纱，以便筒子上的纱线通过导纱器，为弯纱轮钢片和钩针所夹住，垫入针钩内并弯成圈状。针钩带着弯曲纱线移向压针钢板,进行闭口,继而由套圈轮和脱圈轮进行套圈、脱圈和成圈，最后由牵拉卷取机构牵拉坯布并成卷。牵拉卷取机构一般设在针筒上方，但也有设在下方的。台车钩针的针钩弯有凹口，在成圈过程中可夹持弯曲的纱线，不使转移，有利于成圈的均匀性。钩针以2～3枚浇铸在一块针蜡上，机号30以下以2枚浇铸，以上的以3枚浇铸。调换不同粗细的钩针和相应的成圈机件，便可改变机器的机号。针筒直径范围20～178厘米（8～70英寸），机号5～50。台车转速较高,如76厘米（30英寸）针筒直径、12路进线，可达55转/分。此外,台车还具有翻改品种和上机调整简便、加工纱号适用性广和便于操作等优点。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条