1) EDM
电火花
1.
Power Supply for Ultrasonic Motor Applicable to EDM;
适合于电火花加工的超声马达驱动电源的研制
2.
Gas Flow Field Simulation During Ultrasonic Vibration Assisted Gas Medium EDM Based on Fluent Software;
基于Fluent的超声振动-气体介质电火花加工气体流场模拟
3.
Machining Curve Surface Cavities of Mould by Trepanning Technology of EDM;
模具型腔三维曲面的电火花套型加工
2) electric spark
电火花
1.
Analysis and verification of the machining mechanism of air mixed electric spark;
混气电火花加工机理的分析及验证
2.
Evaluation of Uncertainty in Determination of Carbon in Low Alloy Steel by Electric Spark-Direct Reading Spectrometry;
电火花直读光谱法测定低合金钢中碳的测量不确定度评定
3.
Determination of Iron,Silicon,Copper,Manganese,Magnesium, Titanium and Zinc in Pure Aluminum Sheets by Electric Spark Direct Reading Spectrometry;
电火花-直读光谱法测定纯铝薄板中的Fe、Si、Cu、Mn、Mg、Ti、Zn
3) Electrical Discharge
电火花
1.
Numerical simulation of temperature field for electrical discharge strengthened coating;
电火花表面强化层温度场的数值模拟
2.
Research of thermal stress on electrical discharge surface strengthening
电火花表面强化的热应力研究
3.
A new EDM technology-ultrasonic vibration assisted electrical discharge machining in gas was proposed and corresponding experimental equipment was designed.
简述了超声振动辅助气体介质电火花加工原理,并设计开发了相应的实验机床。
4) electrospark
电火花
1.
lnterfacial behavior of filled joints by electrospark overlaying;
填充型电火花精密堆焊接头的界面结合行为
2.
Microstructure and properties of electrospark surface strengthening layers;
电火花表面强化层组织结构和性能的研究
3.
Electrospark surface strengthening technique and machine;
电火花表面强化工艺及设备
5) spark
[英][spɑ:k] [美][spɑrk]
电火花
1.
Signle-Chip Computer-Based Control System for the Spark Machine;
单片机控制系统在电火花机床上的应用
2.
In view of actualities that the internal bore of precision miniature bearing below 2mm is difficult to grind conventionally,the spark grinding of the internal bore is realized initially by adopting two-rod backup structure,increasing the amplitude and the velocity of reciprocating oscillation during process and changing the quasi parameters of electric gauge reasonably.
针对2 mm以下精密微型轴承内孔难以采用常规的磨削方法加工的现状,根据电火花小孔磨削的基本原理,在电火花小孔磨削装置的基础上,采用双辊棒支承工件的结构,加大加工时往复振荡的幅度和速度,合理转换电规准电参数,初步实现了精密微型轴承内孔的电火花磨削。
3.
This paper presents the hardware and software design of control system of spark machine controlled by using 8031 single chip computer.
介绍了一种采用８０３１单片机控制的电火花机床数控系统的软硬件设计，并介绍了其设计思想、控制原理及软件框
6) spark
[英][spɑ:k] [美][spɑrk]
电花，火花
补充资料：电火花
分子式：
CAS号：
性质：电极间击穿放电时的强烈流柱。大量电火花汇集成电弧。电火花的温度高达摄氏数千度，不仅能直接引起可燃物燃烧，还能使金属熔化、飞溅，构成二次火源。产生电火花的处所和操作过程有(1)刀开关、断路器、接触器等电气设备操作过程中。(2)直流电动机的电刷与换向器的滑动接触处、绕线式异步电动机的电刷与滑环的滑动接触处。(3)电气设备或电气线路的绝缘发生过电压击穿、发生短路、故障接地、导线断开或接头松动时。(4)熔断器的熔体断开。(5)雷电放电、静电放电、电磁感应放电等。
CAS号：
性质：电极间击穿放电时的强烈流柱。大量电火花汇集成电弧。电火花的温度高达摄氏数千度，不仅能直接引起可燃物燃烧，还能使金属熔化、飞溅，构成二次火源。产生电火花的处所和操作过程有(1)刀开关、断路器、接触器等电气设备操作过程中。(2)直流电动机的电刷与换向器的滑动接触处、绕线式异步电动机的电刷与滑环的滑动接触处。(3)电气设备或电气线路的绝缘发生过电压击穿、发生短路、故障接地、导线断开或接头松动时。(4)熔断器的熔体断开。(5)雷电放电、静电放电、电磁感应放电等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条