1) Inclusion
[英][ɪn'klu:ʒn] [美][ɪn'kluʒən]
夹杂物
1.
Research on Inclusion Controlling Technology of Low Carbon Al-killed Steel;
低碳铝镇静钢夹杂物控制技术研究
2.
Influence of Electromagnetic Brake in the Continuous Casting on the Non-metallic Inclusion of the Slab;
连铸结晶器电磁制动对铸坯中非金属夹杂物影响的研究
3.
Analysis and Control of Macro Inclusion in Structural Steel Melting by EAF-LF-CC Process;
EAF-LF-CC工艺冶炼的结构钢低倍夹杂物的分析和控制
2) inclusions
夹杂物
1.
Research on inclusions in billet continuous casting of steel ML08Al;
ML08Al冷镦钢连铸坯中夹杂物的研究
2.
New technology for control and removal of inclusions in tundish;
中间包夹杂物的去除与控制新技术
3.
Formation and Control of Inclusions in Si-Mn Cast Steel with High Carbon Content;
高碳硅锰铸钢中夹杂物的形成与控制
3) impurity
[英][ɪm'pjʊərəti] [美][ɪm'pjurətɪ]
夹杂物
1.
1 steel plant,and profound analysis was carried out for the capability of reducing impurity of blowing-argon,ladle reefing,middle-vessel,crystallizer,and the infection of variant deoxidation ability on the content,composition and shape of the impurity in carting blank,through gas-analysis,image-analysis and electron microscope scan.
为了解济钢一炼钢钢水纯净度的实际状况,选择两个典型钢种BC和AH32为分析对象,通过气体分析、图像分析和电子显微镜扫描分析分别对吹氩处理和LF炉精炼处理、中间包和结晶器去除夹杂物的能力及采用不同的脱氧工艺对铸坯夹杂物含量、组成及形态的影响进行了深入分析,找出了全氧和氮的变化规律、夹杂物粒度分布及主要组成,为研究如何降低夹杂物含量和改变夹杂物形态提供了技术基础。
2.
This paper analyzes the effectiveness of removing impurity of the continuous process under the condition of high frequency magentic field.
分析了高频磁场作用下熔体连续处理时夹杂物的去除效率。
3.
Through test and analysis, it is believed that the main cause of failure of the short inlet pipe of main platen header is low smelting purity and high impurity content of steel, and original cracks formed by concentrated impurity along the pipe longitudinally during rolling, which leads to tear-off.
通过试验 ,分析部件失效原因为 :钢材冶炼纯净度低致使夹杂物超标 ,在随后的轧制过程中形成沿管子纵向分布的密集夹杂物构成的原始裂纹 ,从而导致开裂。
4) non-metallic inclusions
夹杂物
1.
There were mainly two types of non-metallic inclusions in the steels,which were the MnS-MnO typed inclusions and TiN-VN typed inclusions.
钢中的非金属夹杂物主要有MnS-MnO类夹杂物和TiN-VN类析出物2个类型,其中MnS-MnO类夹杂物中MnS的质量分数为70%~81%,为塑性夹杂物。
2.
In combination with the practice and application, the microstructure and non-metallic inclusions at different levels in 16MnDR,15CrMoR and 15MnNbR pressure vessel plate was analysied,which provide the basis for an improvement on quality of the higher pressure vessel plate.
文章结合中厚板的生产工艺,对16MnDR、15CrMoR和15MnNbR等压力容器中厚板的显微组织和夹杂物级别进行了分析,为开发更高级别压力容器用钢提供了依据和借鉴。
3.
The microstructure and non-metallic inclusions in the medium thickness CC slab of 135 mm were observed and analyzed by using optical microscope and scanning electron microscopy.
本文利用光学显微镜和扫描电子显微镜对鞍钢中薄板坯连铸连轧机组生产的135mm厚度铸坯的铸态组织结构和夹杂物形貌进行了检验分析,结果显示:中薄板坯的铸态组织结构与传统厚板坯相近,由表面细小等轴晶区、柱状晶区和心部等轴晶区三部分组成。
5) impurities containing Zr
锆夹杂物
1.
The fault between the impurities containing Zr and matrix is not formed during the rolling process but are depend on the microstructure after rolling.
含锆夹杂物与基体间的缝隙,不是在轧制时形成的,而是在轧后由相变后的组织决定的:有铁素体等软质相组织的钢中,夹杂物与基体的缝隙较小;主要由板条等硬质相组成的钢中,夹杂物与基体的缝隙较大。
6) aluminum inclusion
铝夹杂物
1.
Original position statistic distribution analysis of aluminum inclusion in middle-low alloy steel;
中低合金钢中铝夹杂物的原位统计分布分析
2.
The criterion of original position statistic distribution analysis for the aluminum inclusion in steel;
钢中铝夹杂物原位统计分布分析的判据方法
补充资料：夹杂物
夹杂物
【夹杂物】指实物中含带的沙、泥、土、石、稗子等杂物。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条