1) semi-solid
半固态
1.
Application of Microstructural Analysis to the Microstructure Observation of the Semi-solid Alloy;
微观分析方法在半固态组织观察中的应用
2.
Preparation of Semi-solid Billets and Its Slurry by Novel Sloping Plate Process;
新型倾斜板技术制备半固态铝合金坯料和浆料
3.
Study on the Compressive Deformation Behavior of Semi-solid Al-Si-Cu-Mg Alloy;
半固态Al-Si-Cu-Mg合金压缩变形特征的研究
2) semisolid
[英][,semi'sɔlid] [美][,sɛmɪ'sɑlɪd]
半固态
1.
Preparing semisolid billet of Al-3%Mg alloy by sloping cooling/shearing process;
倾斜式冷却剪切技术制备Al-3%Mg半固态合金坯料
2.
Experimental studies on making process of semisolid 60Si2Mn spring steel billets;
60Si2Mn弹簧钢半固态坯料制备的实验研究
3.
Study on Rheologic Properties of Semisolid AZ91D Alloys;
AZ91D镁合金半固态静态剪切流变特征的研究
3) Semi-solid State
半固态
1.
Billet preparation is a key point during semi-solid state forming.
坯料制备是半固态成形技术中的一个关键问题,以40CrN iMo钢为研究对象,提出了循环淬火法制备半固态坯料的方法。
2.
The growth law of grain in reactive spray deposited TiC_p/7075 Al alloy was studied and compared with that of spray formed 7075 Al alloy at semi-solid state.
采用原位反应喷射沉积法制备TiC_p／7075半固态铝合金坯料,在600℃保温10—60 min,研究半固态二次加热过程中合金的晶粒长大规律,并与喷射沉积7075铝合金进行对比分析,结果表明,添加原位TiC颗粒后,合金的晶粒长大指数由2增加到3,晶粒长大速率明显减慢,其原因是添加TiC颗粒后合金晶粒长大激活能增加1倍左右,使得合金的晶粒长大更加困难,显示出原位TiC颗粒对喷射沉积7075铝合金的晶粒长大具有显著的抑制作用。
3.
The squeezed-casting formability of AZ91D magnesium alloy in semi-solid state was studied.
研究了AZ91D镁合金在不同半固态温度下的挤压铸造。
4) semi solid
半固态
1.
Based on the principle concentred the flow of metal slurry in gap between the two rotating tubes with groove showing high shear stress field, the equipment used in preparation of the semi solid magnesium alloy was developed and the new approach of how to develop magnesium alloy was explored.
通过计算分析 :AZ91合金的半固态流变成形温度区间为 5 5 0～ 5 90℃ ,同时得到了AZ91合金的固相体积分数fs(固相率 )随温度变化的关系曲线。
2.
Based on the behavior characters of pressure and flow velocity during semi solid AlSi7Mg slurry filling processes, a three dimensional model of slurry flow coupled with apparent viscosity was established.
在充分考虑半固态AlSi7Mg合金触变充型过程中压力和速度变化特征基础上 ,建立耦合半固态表观粘度的三维流场数学模型 ,确定固定流量的入流边界条件和约束滑动型壁边界条件以及保持入流温度不变的初始条件 ,并采用SOLA VOF法对铝合金件的触变充型过程进行了模拟计算。
5) semisolid state
半固态
1.
The method of DSC( Differential Scanning Calorimeter) is used to study the relation of the fraction of solid as a function of temperature in aluminum alloys in the semisolid state during reheating.
利用差热扫描分析法(Differential Scanning Calorimeter)研究半固态铝合金ZL101在二次重熔过程中固相分数随温度变化的规律。
2.
The mechanical behavior of 7A04 alloy in the semisolid state has been studied through isothermal compression tests.
通过半固态等温压缩实验,研究了7A04合金在半固态压缩过程中的力学行为。
6) semi-solidification
半固态凝固
补充资料：半刺
1.指州郡长官下属的官吏，如长史﹑别驾﹑通判等。 2.针灸五刺之一。刺入较浅，故称半刺。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条