1) corrosion resistance
耐蚀性
1.
Effect of carbon content and microstructure on the corrosion resistance of low alloy steels;
碳含量和组织类型对低合金钢耐蚀性的影响
2.
Effect of carbon nanotubes on the corrosion resistance of laserclad Ni60 alloy coatings;
碳纳米管对Ni60激光熔覆层的耐蚀性影响
3.
Electrochemical measurement of corrosion resistance and microstructure analyse of supersonic arc spray coating;
超音速电弧喷涂涂层耐蚀性的电化学测试及组织分析
2) Anti-corrosion
耐蚀性
1.
Study of Alkaline electroless Ni-P/CeO_2 Composite Coating and its Anti-corrosion Properties;
碱性化学镀Ni-P/CeO_2复合镀层及其耐蚀性研究
2.
Oxidation coatings were produced on AM60B Mg alloy substrates using the Microarc oxidation(MAO) technique in order to improve the anti-corrosion property of Mg alloy.
5%NaCl溶液中的动电位极化测试表明,微弧氧化处理使镁合金的耐蚀性能得到了明显提高。
3.
The combinatorial method has been widely used in various areas related with alloy materials for their phase-diagram,mechanical properties,anti-corrosion properties,and so on,and shows obviously its advantage in fast discovery and optimization of new kinds of alloy,with the help of the successful development and applications of nano-indentation,microstructure analysis and composition ana.
近年来,随着微小样品的结构和成分检测系统、纳米压痕测试系统等的发展,先进组合材料芯片技术在合金材料研究领域的应用日益深入,包括精细相图研究、合金的力学/磁学/耐蚀性能等研究,充分展示了组合方法在新型合金材料研发进程中所表现的快速和高效双重特点。
3) corrosion-resistance
耐蚀性
1.
Effects of process conditions on microstructure and corrosion-resistance of electrodepositing Pd-Co alloy;
电沉积条件对Pd-Co合金微观相结构和耐蚀性的影响
2.
The influence of rare earth on the microstructure and corrosion-resistance of hot-dipped aluminum in well circumstance;
稀土对渗铝钢组织及其在油田环境下耐蚀性的影响
3.
The corrosion-resistance of RE-Ni-W-P-SiC composite coatings prepared by pulsing current(p.
采用腐蚀溶液浸泡、绘制阳极极化曲线和中性盐雾试验三种方法研究了稀土(RE)-Ni-W-P-SiC脉冲复合镀层的耐蚀性。
4) anticorrosion
[,æntikə'rəuʒən]
耐蚀性
1.
Influence of Impurities on the Anticorrosion of High Purity Magnesium Alloys;
杂质对高纯镁合金耐蚀性的影响
2.
58 wt% C have fewer microcracks,exhibiting much better anticorrosion than SU.
58%C组成,镀层中无显微裂纹,在3%NaCl溶液中的耐蚀性明显优于SUS304不锈钢。
3.
Black conversion film with non-chromate was obtained on a cast aluminum alloy by chemical methods,and the anticorrosion properties of the film were evaluated by means of dropping test.
用无铬化学方法在铸铝合金表面制得黑色转化膜,利用点滴试验评价了膜的耐蚀性能。
5) erosion resistance
耐蚀性
1.
Research on Gd_(1-x)Cu_x erosion resistance;
Gd_(1-x)Cu_x合金耐蚀性的研究
2.
And the effect of adding nm TiO2 to the hardness and erosion resistance of composite electroplate coating is analyzed.
用电镀的方法制备出了Ni-TiO2纳米复合电镀层,讨论了表面活性剂、阴极电流密度、搅拌速率等对复合镀层硬度的影响,并分析了纳米TiO2的加入对复合镀层硬度、耐蚀性的影响情况。
3.
In order to improve the wear resistance and erosion resistance of copper crystallizer,Ni60A coating on copper by laser cladding was investigated.
为了提高铜质结晶器的耐磨性和耐蚀性,在纯铜基体上进行了激光熔覆Ni60A涂层的试验研究。
6) Corrosion resistance/Erosion resistance
耐蚀性/耐磨蚀性
补充资料：晦蚀
1.暗淡而亏缺。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条